8932
Federal Register /
Vol. 60, No. 32 /
Thursday, February 16, 1995 /
Rules and Regulations
engine into a shop for maintenance involving
the separation of any major flange.
(g) For the purpose of this AD, piece-part
exposure is defined as disassembly and
removal of the stage 3–9 spool from the
HPCR rotor.
(h) An alternative method of compliance or
adjustment of the compliance time that
provides an acceptable level of safety may be
used if approved by the Manager, Engine
Certification Office. The request should be
forwarded through an appropriate FAA
Principal Maintenance Inspector, who may
add comments and then send it to the
Manager, Engine Certification Office.
Note: Information concerning the existence
of approved alternative method of
compliance with this AD, if any, may be
obtained from the Engine Certification Office.
(i) Special flight permits may be issued in
accordance with sections 21.197 and 21.199
of the Federal Aviation Regulations (14 CFR
21.197 and 21.199) to operate the aircraft to
a location where the requirements of this AD
can be accomplished.
(j) The actions required by this AD shall be
done in accordance with the following
service bulletins:
Document No.
Pages
Revision
Date
GE CF6–50, SB No. 72–1000 ....................................................................................................................
1–37
2
Sept. 9, 1993.
Total pages: 37.
GE CF6–80A SB No. 72–583 ....................................................................................................................
1–34
4
Sept. 15, 1993.
Total pages: 34.
This incorporation by reference was
approved by the Director of the Federal
Register in accordance with 5 U.S.C. 552(a)
and 1 CFR part 51. Copies may be obtained
from General Electric Aircraft Engines, CF6
Distribution Clerk, Room 132, 111 Merchant
Street, Cincinnati, OH 45246. Copies may be
inspected at the FAA, New England Region,
Office of the Assistant Chief Counsel, 12 New
England Executive Park, Burlington, MA; or
at the Office of the Federal Register, 800
North Capitol Street, NW., suite 700,
Washington, DC.
(k) This amendment becomes effective on
March 20, 1995.
Issued in Burlington, Massachusetts, on
January 31, 1995.
Donald F. Perrault,
Acting Manager, Engine and Propeller
Directorate, Aircraft Certification Service.
[FR Doc. 95–3248 Filed 2–15–95; 8:45 am]
BILLING CODE 4910–13–P
DEPARTMENT OF THE TREASURY
Internal Revenue Service
26 CFR Part 1
[TD 8580]
RIN 1545–AN06
Disposition of an Interest in a Nuclear
Power Plant; Correction
AGENCY
:
Internal Revenue Service (IRS),
Treasury.
ACTION
:
Correction to final regulations.
SUMMARY
:
This document contains
corrections to the final regulations (TD
8580), which was published in the
Federal Register for Tuesday, December
27, 1994 (59 FR 66471). The final
regulation relates to certain Federal
income tax consequences of a
disposition of an interest in a nuclear
power plant by a taxpayer that has
maintained a nuclear decommissioning
fund with respect to that plant.
EFFECTIVE DATE
:
December 27, 1994.
FOR FURTHER INFORMATION CONTACT
:
Peter C. Friedman, (202) 622–3110 (not
a toll-free number).
SUPPLEMENTARY INFORMATION
:
Background
The final regulations that are the
subject of these corrections are under
section 468A of the Internal Revenue
Code.
Need for Correction
As published, TD 8580 contains errors
which may prove to be misleading and
are in need of clarification.
Correction of Publication
Accordingly, the publication of final
regulations (TD 8580), which were the
subject of FR Doc. 94–31428, is
corrected as follows:
§ 1.468A–3
[Corrected]
1. On page 66474, column 1,
preceding § 1.468A–3, in instructional
‘‘Par. 4.’’, paragraph 2a is added
immediately following the text of
paragraph 2 to read as follows:
2a. In newly designated paragraph
(h)(1)(vi), the reference ‘‘paragraph
(h)(1)(viii)’’ is removed and ‘‘paragraph
(h)(1)(vii)’’ is added in its place.
§ 1.468A–5
[Corrected]
2. On page 66474, column 2,
preceding § 1.468A–5, in instructional
‘‘Par. 5.’’, paragraph 3a is added
immediately following the text of
paragraph 3 to read as follows:
3a. In newly designated paragraph
(b)(2)(vii) introductory text, the
reference ‘‘paragraph (b)(2)(vi)’’ is
removed from the last sentence and
‘‘paragraph (b)(2)(vii)’’ is added in its
place.
Dale D. Goode,
Federal Register Liaison Officer, Assistant
Chief Counsel (Corporate).
[FR Doc. 95–3770 Filed 2–15–95; 8:45 am]
BILLING CODE 4830–01–U
DEPARTMENT OF JUSTICE
Office of the Attorney General
28 CFR Part 0
[AG Order No. 1948–95]
Establishment of the Office of
Community Oriented Policing Services
AGENCY
:
Department of Justice.
ACTION
:
Interim rule with request for
comments.
SUMMARY
:
This order will amend the
Department of Justice organization
regulations to reflect the creation of the
Office of Community Oriented Policing
Services. This new office will
implement certain grant programs
authorized by the Violent Crime Control
and Law Enforcement Act of 1994. This
order will provide the public with a list
of the duties of the Director of the Office
of Community Oriented Policing
Services, and will amend the Code of
Federal Regulations in order to reflect
accurately the Department’s internal
management structure. Finally, this
order makes applicable to the Office of
Community Oriented Policing Services
certain parts of the Code of Federal
Regulations currently applicable only to
the Office of Justice Programs.
DATES
:
Interim rule effective February
16, 1995, comments must be received on
or before April 3, 1995.
ADDRESSES
:
Comments may be mailed to
the Office of the General Counsel, Office
of Community Oriented Policing
Services, U.S. Department of Justice,
P.O. Box 14440, Washington, DC 20044,
or delivered to Suite 300, 633 Indiana
Avenue, N.W., Washington, DC between
9 a.m. and 5:30 p.m. Comments received
may also be inspected at Suite 300
between 9:15 a.m. and 5:15 p.m.
FOR FURTHER INFORMATION CONTACT
:
L. Anthony Sutin, General Counsel,
Office of Community Oriented Policing
File Type | application/pdf |
File Title | Document |
Subject | Extracted Pages |
Author | U.S. Government Printing Office |
File Modified | 2007-10-03 |
File Created | 2007-10-03 |