Waivers of In Vivo Demonstration of Bioequivalence of Animal Drugs in Soluble Powder Oral Dosage Form Products and Type A Medica

CONTAINS NON-BINDING RECOMMENDATIONS

#171
Guidance for Industry
Waivers of In Vivo Demonstration of Bioequivalence of Animal Drugs in Soluble
Powder Oral Dosage Form Products and Type A Medicated Articles
(This version of the guidance replaces that which was made available on February 16, 2006. This
guidance document has been revised to address some confusion among sponsors regarding
the recommendations contained in the document. The revisions clarify the guidance’s key concepts. No
new concepts have been introduced and the scope of the guidance has not changed. The revisions: (1)
update terminology to indicate that the GFI is not just applicable to applications for generic drugs; (2)
move lengthy and informative footnotes into the body of the text so that they are not overlooked; and (3)
restructure sections (specifically Section IV) to improve the flow and readability of the document and to
highlight important details (e.g., analytical data) that the sponsor should submit to CVM in support of
their waiver request. )

Comments and suggestions regarding this guidance should be sent to the Division of Dockets
Management (HFA-305), Food and Drug Administration, 5630 Fishers Lane, Room 1061,
Rockville, MD 20852. All comments should be identified with the Docket No. 2004D-0283.
Comments also may be submitted electronically on the Internet at
http://www.fda.gov/dockets/ecomments.
For questions regarding the guidance document, contact the following individuals:
Biopharmaceutics and Pharmacokinetics: Marilyn Martinez, Center for Veterinary Medicine
(HFV-130), Food and Drug Administration, 7500 Standish Place, Rockville, MD 20855, 240276-8357, e-mail: [email protected].
Manufacturing Chemistry/Solubility Concerns: Julie Bailey, Center for Veterinary Medicine
(HFV-140), Food and Drug Administration, 7500 Standish Place, Rockville, MD 20855, 240276-8270, email: [email protected].
Generic Drug Approval Requirements: John K. Harshman, Center for Veterinary Medicine
(HFV-104), Food and Drug Administration, 7500 Standish Place, Rockville, MD 20855, 240276-8197, email: [email protected].
Additional copies of this guidance document may be requested from the Communications Staff
(HFV-12), Center for Veterinary Medicine, Food and Drug Administration, 7519 Standish Place,
Rockville, MD 20855, and may be viewed on the Internet at http://www.fda.gov/cvm.
Paperwork Reduction Act Public Burden Disclosure Statement
According to the Paperwork Reduction Act of 1995, a collection of information should display a valid Office of
Management and Budget (OMB) control number. The valid OMB control number for this information collection is
0910-[0575] (Expires [01/31/2009]). The time required to complete this information collection is estimated to
average, for Water Soluble Powders, 5 hours per response for the Same Formulation/Manufacturing Process

CONTAINS NON-BINDING RECOMMENDATIONS
Approach and 10 hours per response for the Same API/Solubility Approach; for Type A Medicated Articles, the
time required to complete this information collection is estimated to average 5 hours per response for the Same
Formulation/Manufacturing Approach, and 20 hours per response for the Same API/Solubility Approach, including
the time to review instructions, search existing data resources, gather the data needed, and complete and review the
information collection. Send comments regarding this burden estimate or suggestions for reducing this burden to:
John K. Harshman, Center for Veterinary Medicine (HFV-104), Food and Drug Administration, 7500 Standish
Place, Rockville, MD 20855, 240-276-8197, email: [email protected].
An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless
it displays a currently valid OMB control number.

_____________________________________________________________________________
U.S. Department of Health and Human Services
Food and Drug Administration
Center for Veterinary Medicine (CVM)
October 6, 2008

__________________________________________________________________

Page 2 of 12

CONTAINS NON-BINDING RECOMMENDATIONS

Guidance for Industry
Waivers of In Vivo Demonstration of Bioequivalence of Animal Drugs in Soluble
Powder Oral Dosage Form Products and Type A Medicated Articles 1
This guidance represents the agency’s current thinking on this topic. It
does not create or confer any rights for or on any person and does not
operate to bind FDA or the public. You can use an alternative approach
if the approach satisfies the requirements of the applicable statute(s) and
regulation(s). If you want to discuss an alternative approach, contact the
FDA staff responsible for implementing this guidance. If you cannot
identify the appropriate FDA staff, call the appropriate number listed on
the title page of this guidance.

I. PURPOSE
This document describes how the Center for Veterinary Medicine (CVM) intends to evaluate
requests for waiving the requirement for submitting in vivo data demonstrating the
bioequivalence of animal drugs in soluble powder oral dosage form products and Type A
medicated articles. It expands upon CVM’s Bioequivalence Guidance, 2 particularly the section
on Criteria for Waiver of In Vivo Bioequivalence Study.
This guidance is applicable to generic investigational new animal drug files (JINAD) and
abbreviated new animal drug applications (ANADA). Although the recommendations in this
guidance reference generic drug applications, the general principles described are also applicable
to new animal drug applications (NADA), investigational new animal drug files (INAD), and
supplemental NADAs.
The recommendations in this guidance are premised on the assumption that a sponsor will be
bridging between identical dosage forms (e.g., Type A medicated article for use in complete feed
to Type A medicated article for use in complete feed; soluble powder for use in drinking solution
to soluble powder for use in drinking solution). Therefore, it may not be appropriate to use the
recommendations in the guidance to compare the solubility of two products where the API will
be administered in differing manners (e.g., drinking water versus complete feed, complete feed
for administration throughout the day versus top dress). CVM encourages sponsors to contact
the Center to discuss the applicability of this guidance document to that type of comparison.
1

This guidance has been prepared by the Office of New Animal Drug Evaluation in the Center for Veterinary
Medicine at the Food and Drug Administration.
2
CVM Guidance for Industry # 35, “Bioequivalence Guidance,” November 8, 2006.

Page 3 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
II. BACKGROUND
In general, an ANADA must include information to show that the proposed product and
reference product are bioequivalent.3 This requirement is patterned very closely on the human
generic drug provision. 4
The Center for Drug Evaluation and Research’s (CDER) regulations implementing the
bioequivalence requirement are at 21 CFR part 320. In most cases, there must be an in vivo
demonstration of no significant differences in the rate and extent of drug availability associated
with the proposed and reference drug products when administered at the same molar dose under
similar conditions. 5 In certain circumstances, however, the demonstration of bioequivalence does
not need to be established on the basis of in vivo studies. 6 For several categories of drugs,
including oral solutions, bioequivalence is considered self-evident under specified conditions. 7
In certain circumstances, the bioequivalence of solid oral dosage forms can be documented using
in vitro approaches. 8 For highly soluble, highly permeable, rapidly dissolving, and orally
administered drug products, documentation of bioequivalence using an in vitro approach is
appropriate based on a biopharmaceutics classification system. 9
CVM has not issued regulations regarding the bioequivalence requirement for generic products.
It has issued guidance on in vivo bioequivalence studies, which includes a list of some of the
product categories, including oral solutions and other solubilized forms that may be eligible for
an in vivo bioequivalence waiver. 10 The guidance states that: “in general, the generic product
being considered for a waiver contains the same active and inactive ingredients in the same
dosage form and concentration and has the same pH and physico-chemical characteristics as an
approved pioneer product.” 11 This guidance provides additional information and
recommendations regarding bioequivalence waivers for soluble powder oral dosage form
products intended for use in animal drinking water and Type A medicated articles intended for
use in animal feed.

3
4

Section 512(n)(1)(E) of the Federal Food, Drug, and Cosmetic Act (the Act).
Section 505(j)(2)(A)(iv) of the Act.

5

21 CFR 320.1(e) and 320.21(b). CDER's guidance on how to meet the bioequivalence requirements set forth in
21 CFR part 320 is contained in: CDER Guidance for Industry: Bioavailability and Bioequivalence Studies for
Orally Administered Drug Products — General Considerations, March 2003.
6
21 CFR 320.21(b),(f) and 320.22.
7
21 CFR 320.22(b)(3).
8
CDER Guidance for Industry: Bioavailability and Bioequivalence Studies for Orally Administered Drug Products
— General Considerations, March 2003, Page 10.
9
Id. Additional information about these waivers and the biopharmaceutics classification system CDER uses are in:
CDER Guidance for Industry: Waiver of In Vivo Bioavailability and Bioequivalence Studies for ImmediateRelease Solid Oral Dosage Forms Based on a Biopharmaceutics Classification System, August 2000.
10
CVM Guidance for Industry # 35, “Bioequivalence Guidance”, November 8, 2006.
11
Id., Page 7.

Page 4 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
FDA’s guidance documents, including this guidance, do not establish legally enforceable
responsibilities. Instead, guidances describe the Agency’s current thinking on a topic and
should be viewed only as recommendations, unless specific regulatory requirements are
cited. The use of the word “should” in Agency guidances means that something is
suggested or recommended, but not required.
III. DISCUSSION
This guidance describes how CVM intends to evaluate requests to waive the requirements for
conducting an in vivo bioequivalence study, hereafter referred to in this guidance as
“biowaivers,” for certain categories of animal drugs.
A. Waivers for soluble powder oral dosage form products. CVM believes it will usually be
appropriate to grant biowaivers for oral dosage forms known as “soluble powders.” Such
products are intended for administration to animals via the drinking water that, under most
husbandry systems, is provided on an ad libitum basis.
The conceptual basis for granting biowaivers for “soluble powders” is that once a drug is in
solution prior to administration, the product's formulation will usually not influence the
bioavailability of the active ingredient. This is because, from a mechanistic perspective, the
rate-limiting step in systemic drug absorption will be: a) the rate of gastric transit; and b) the
permeability of the active ingredient across the gastrointestinal (GI) mucosal membranes. Both
of these variables are formulation-independent. Similarly, if a drug acts locally within the GI
tract (not systemically absorbed), the local exposure to the dissolved drug in the proposed and
reference product formulations will be equivalent if the drug is already in solution because the
rate-limiting step is drug movement down the GI tract and its lateral diffusion across the
viscous intestinal contents. The only exceptions of which CVM is aware are when the
formulation contains substances other than the active ingredient that could cause a direct
pharmacologic effect (e.g., altered GI transit time, membrane permeability, or drug
metabolism), or when there is inactivation of the active ingredient by, for example, a chelating
agent. Therefore, in making waiver decisions for soluble powders, CVM intends to evaluate 1)
solubility data provided by the sponsor to ensure that, prior to administration, the product will
go into solution under the range of physical conditions that a user of the product would
typically encounter when adding the soluble powder to animal drinking water in the field; and
2) the product's formulation to ensure that there are no differences between the reference and
proposed product formulations likely to adversely affect the performance of the proposed
product, e.g., cause adverse pharmacologic effects or alter active ingredient bioavailability.
B. Waivers for Type A medicated articles. With respect to eligibility for a biowaiver, CVM
believes there is no reasonable basis for drawing a distinction between active ingredients
intended for administration to animals via drinking water and active ingredients intended to
be administered via feed, provided these drug substances have similar physico-chemical

Page 5 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
properties, particularly solubility. A soluble drug, present in a Type A medicated article and
mixed into a feed matrix, rapidly dissolves when exposed to the fluids of the GI tract. From
a mechanistic perspective, if such a drug readily goes into solution across the range of
physiological pH values, it will likely go rapidly into solution when exposed to the fluids in
the GI tract. Accordingly, such medicated feeds will effectively behave as oral solutions
shortly after administration. As such, CVM also intends to review biowaiver requests that
involve active ingredients in Type A medicated articles on the basis of a demonstration of
solubility and the product's formulation to ensure that there are no ingredients in the
proposed formulation likely to cause adverse pharmacologic effects or inactivate active
ingredients. Determining appropriate methods for ascertaining product bioequivalence for
Type A medicated articles that contain active ingredients that are not classified as water
soluble may prove more challenging and are not the subject of this guidance.
1. Type A medicated articles and feed formulation effects. Feed constituents may affect the
bioavailability of the active ingredients in a Type A medicated article. CVM believes,
however, that this should not be a factor in considering a biowaiver request since the
variability in feed constituents between the reference and proposed Type A medicated
articles should not be greater than the natural variations that can occur in the final feed to
which the animal will be exposed, whether that feed contains the proposed product or the
reference product.
2. Type A medicated articles containing biomass products. Many antimicrobials, and
some drugs in other pharmacologic classes, that may become the active ingredients of
soluble powder oral dosage form products and Type A medicated articles are produced
through fermentation processes. In soluble powder oral dosage form products, the
active ingredients typically are subjected to substantial extraction and purification
following the fermentation process. While the active ingredients in some Type A
medicated articles are virtually identical in purity to these soluble powder oral dosage
form products, the active ingredients in others may contain significant quantities, or
even all, of the fermenting microorganisms and nutrient substrate (biomass) associated
with the fermentation process.
Because dried fermentation biomass derived from a number of different fermentation
processes is a well-accepted and routinely used feed ingredient, CVM will consider the
potential for the biomass component of a Type A medicated article to cause adverse
pharmacologic effects or inactivate active ingredients in the same manner that it
considers these effects with respect to other feed ingredients. Generally, CVM would
deny a biowaiver on the basis of such potential feed ingredient effects only when it has
information indicating that a specific feed ingredient may have such an effect.
However, whether a biowaiver would be denied based on potential adverse
pharmacologic effects or effects on active ingredient bioavailability and whether a
proposed product’s approval would be denied because of safety concerns associated
Page 6 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
with inactive ingredients, such as biomass components, are two different issues. The
latter issue is outside the scope of this guidance document, and questions related to this
aspect of biomass Type A articles should be addressed to the office of the Director,
Office of New Animal Drug Evaluation.
C. Effect of a grant of a bioequivalence waiver. As noted above, the granting of a waiver of
the need to submit in vivo bioequivalence study data does not imply that a product is
approvable. For product approval, all of the applicable legal requirements must be met.
If a waiver of the need to submit in vivo bioequivalence studies is granted, the sponsor may
request a waiver for the need to submit tissue residue depletion data. 12 If CVM waives the
requirement to submit a tissue residue depletion study, it will assign the withdrawal time
established for the pioneer product to the generic product.
IV. GUIDANCE
For soluble powder oral dosage form products and Type A medicated articles, CVM
recommends that requests to waive the requirement to establish bioequivalence through in vivo
studies (blood level bioequivalence or clinical endpoint bioequivalence) be made either by a
comparison of formulations or a demonstration of solubility. Sponsors may make these waiver
requests prior to submitting an ANADA.
A. Comparison of Formulations. For both soluble powder oral dosage form products and
Type A medicated articles, CVM is likely to grant a biowaiver if the sponsor can show that
the proposed soluble powder oral dosage form product or Type A medicated article contains
the same active and inactive ingredient(s) and is produced using the same manufacturing
processes as the approved reference product or article. If this approach is selected, CVM
recommends that the sponsor of the proposed product for which a biowaiver is being
requested provide: 1) sufficient evidence that the proposed product contains the same active
and inactive ingredient(s) as the reference product, 2) composition statements for both the
proposed product and the reference product and 3) a description of the proposed and
reference products’ manufacturing processes. This approach is probably practical only for
situations in which the sponsor of the proposed product also manufactures or, perhaps,
formerly manufactured the reference product as well.
B. Demonstration of Solubility. The following sections summarize the main elements associated
with the request for biowaivers based upon the demonstration of the solubility of soluble powder
oral dosage form products or the solubility of active ingredients in the Type A medicated
articles:
1. Composition Statement. The applicant should submit a composition statement for the
proposed product.

12

As described in the CVM guidance #35, “Bioequivalence Guidance,” October 9, 2002, Pages 24-26.

Page 7 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
2. General Criteria for Soluble Powders and Type A Medicated Articles. In order for a
proposed drug product to be eligible for a biowaiver, CVM recommends the following
criteria be met:
a. Soluble powder oral dosage form products. A biowaiver may be granted if the proposed
product contains the same active ingredient(s) as the reference product, there are no
ingredients in the proposed product's formulation likely to cause adverse pharmacologic
effects or inactivate active ingredients, and the product is soluble under the range of
physical conditions that a user of the product would typically encounter when adding the
soluble powder to animal drinking water (i.e., well or municipal water) in the field.
b. Type A medicated articles. A biowaiver may be granted if the proposed product contains
the same active ingredient(s) as the reference product, the active ingredient is soluble,
and there are no ingredients in the proposed product's formulation likely to cause adverse
pharmacologic effects or inactivate active ingredients. CVM recommends the following
criteria be used to support the request for a biowaiver of a Type A medicated article:
i. Information about the Active Ingredient. CVM recommends that the active ingredient
used to support a biowaiver request be provided from the same supplier of the active
ingredient that will be used to formulate the proposed product during production. In
addition to the information requested above, CVM recommends that the applicant
provide the following relevant information regarding the active ingredient in the
waiver request for the proposed product:
1. USP Active Ingredient. Submit a certificate of analysis (COA) for an active
ingredient that complies with a USP monograph. This may suffice as evidence of
equivalence with the active ingredient of the reference product.
2. Non-USP Active Ingredient or Multiple Active Ingredients (e.g., bambermycins).
CVM recommends that the applicant provide sufficient analytical evidence,
including structural characterization (e.g., nuclear magnetic resonance, mass
spectroscopy), to confirm that the identity and/or ratio of the active ingredient
components are equivalent to those in the reference product.
3. Active Ingredients containing Biomass Materials. CVM recommends that the
applicant provide information about the composition of the biomass and identify
the bacterial strain, including its source, used in the fermentation process.
ii. Approaches for Demonstrating Solubility of the Active Ingredient. CVM
recommends that the applicant demonstrate solubility of the active ingredient using
one of the two approaches described below in conjunction with the experimental
guidelines described in Section iii below.
1. “USP definition” approach. CVM believes that for an active ingredient to be
considered “soluble” with respect to a biowaiver request, it should be “very

Page 8 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
soluble,” “freely soluble,” or “soluble” as these terms are defined in Table 1. 13
Solubility should be determined across a defined pH range (see Section iii below).
Table 1. Values for estimating drug aqueous solubility based upon “USP definition”
Descriptive Term

Appropriate Volume of Aqueous Solvent In Milliliters Per Gram
of Solute

Very soluble

Less than 1 part solvent needed to dissolve 1 part solute

Freely soluble

From 1 to 10 parts solvent needed to dissolve 1 part solute

Soluble

From 10 to 30 parts solvent needed to dissolve 1 part solute

Sparingly soluble

From 30 to 100 parts solvent needed to dissolve 1 part solute

Slightly soluble

From 100 to 1000 parts solvent needed to dissolve 1 part solute

Very slightly soluble

From 1000 to 10,000 parts solvent needed to dissolve 1 part solute

Practically insoluble

More than 10,000 parts solvent needed to dissolve 1 part solute

2. “Dosage adjusted” approach. In this approach, the aqueous solubility, across
a defined pH range, should be evaluated according to the highest expected
mg/kg daily intake of a drug and the gastric fluid volume of the target animal
species. If the daily dose can be shown to be soluble in the gastric volume
under the most conservative intended conditions of use (largest dose to fluid
volume ratio), CVM believes the drug should be considered soluble. This
method of defining drug solubility is similar to that described for categorizing
compounds when using the Biopharmaceutics Classification System (BCS) 14
and to the BCS-based approach described in CDER guidance. 15 In this case,
the appropriate fluid volume for testing drug solubility depends upon the
target animal species for which the medicated feed is intended. If a Type A
medicated article is to be used in the manufacture of medicated feeds across
several animal species, the most conservative condition (largest dose to fluid
volume ratio) should provide the basis for determining whether the drug is
soluble. The sponsor should provide the estimated daily drug intake (mg/kg
body weight) based on the labeled drug concentration (e.g., grams of drug per
ton) in the feed administered to the animal (e.g., a Type C medicated feed)
and the amount of feed (kg/day) expected to be consumed by an individual
animal. When using this approach, we recommend using the species-specific
animal weight and fluid volume estimates summarized in Table 2.
13

The United Stated Pharmacopeia, USP 30, NF 25, 2007.
GL Amidon, H Lennernas, VP Shah, JR Crison, A theoretical basis for a biopharmaceutics drug classification:
the correlation of in vitro drug product dissolution and in vivo bioavailability. Pharm. Res., 12 (1995), 413-420.
15
CDER Guidance for Industry: Waiver of In Vivo Bioavailability and Bioequivalence Studies for ImmediateRelease Solid Oral Dosage Forms Based on a Biopharmaceutics Classification System, August 2000.
14

Page 9 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
Table 2. Values for estimating drug solubility based upon “dosage adjusted” methoda,b,c
Body weight
Gastric volume
(for estimating drug intake) (to be used as volume of solvent)

Species

a

Cattle

600 kg

200 Liters (rumen)

Pre-ruminating calf

60 kg

2 Liters

Swine

200 kg

8 Liters

Horse

450 kg

18 Liters

Chicken

2.5 kg

0.1 Liters

Turkey

10 kg

0.4 Liters

Gastric volume estimate for cattle, swine and horses are based upon values reported in, ME Ensminger, JE
Oldfield and WW Heinemann, Feeds and Nutrition, 1990, Ensminger Publishing Company, California, p 53.

b

Volume, based upon daily water consumption, is based upon values reported in GD Goldstein and E Skadhauge,
Renal and extrarenal regulation of body fluid composition, In: Avian Physiology, 2000, GC Whittow, ed.,
Academic Press, Florida, pp 265-291 and Average Daily and Annual Water Requirements, Government of
Alberta Canada, http://www1.agric.gov.ab.ca/app19/calc/livestock/waterreq_dataentry2.jsp

c

Animal weights are based upon the following references: NRC, Nutrient Requirements of Swine 1988), poultry
(NRC, Nutrient Requirements of Poultry 1998), and beef cattle (NRC, Nutrient Requirements of Beef Cattle 1996).

CVM assumes the amount of medicated feed consumed per day and the gastric
volume will vary proportionally with animal age. Therefore, we recommend
that the solubility assessment within a given target animal species be based
upon only one solute/solvent ratio. If the daily dose can be shown to be soluble
in the gastric volume under the most conservative intended conditions of use,
the drug should be determined to be soluble.
iii. Experimental Test Conditions for Demonstrating Solubility. When establishing
solubility of the active ingredient under either the USP definition or dosage adjusted
approach, CVM recommends that the applicant submit data collected using the
experimental conditions described below. These recommendations are based on
CDER Guidance for Industry: Waiver of In Vivo Bioavailability and
Bioequivalence Studies for Immediate-Release Solid Oral Dosage Forms Based on
a Biopharmaceutics Classification System, August 2000, section titled
“Determining Drug Substance Solubility Class” (page 3). CVM has modified
CDER's recommendations to take into account the unique conditions associated
with the use of animal drugs in drinking water and feed.
1. The solubility data should be generated in aqueous media with pH values of
approximately 1.2, 4.6 and 7.5. Standard buffer solutions described in the USP
are considered appropriate for use in solubility studies. If these buffers are not

Page 10 of 12

CONTAINS NON-BINDING RECOMMENDATIONS
suitable for physical or chemical reasons, other buffer solutions can be used
after consultation with CVM.
2. The temperature of the pH-solubility profile testing for the active ingredient
should be maintained at 37 ± 1oC throughout the study to ensure solubility is not
affected by variation in temperature.
3. Solution pH should be verified after addition of the drug substance to the buffer.
If the pH changes significantly after addition of the drug substance, then the
buffers selected are either inadequate or the pH should be adjusted back to the
original pH prior to testing for solubility.
4. A minimum of three replicate determinations of solubility in each pH condition
is recommended. Depending on study variability, additional replication may be
necessary to provide a reliable estimate of solubility.
5. As visual determination of solubility is insufficient, it is recommended that
concentration of the drug substance in selected buffers (or pH conditions) be
determined using a suitably validated assay procedure for the specific type of
sample to be tested.

Page 11 of 12

CONTAINS NON-BINDING RECOMMENDATIONS

Can the active ingredient be defined as soluble using either the USP or dosage
adjusted approach?

YES

Are any ingredients
in the generic
formulation likely
to alter GI transit
time, membrane
permeability, or
drug metabolism or
inactivate the active
ingredient?

NO

YES

Waiver is
likely to be
denied

NO

NO

Are the generic
product's active
ingredients, inactive
ingredients, and
manufacturing
processes the same
as those of the
pioneer product?

YES
Waiver is likely
to be granted

Figure 1 - Flow diagram of a typical biowaiver decision tree for Type A medicated articles

Page 12 of 12