2025ss06

2025ss06.docx

NESHAP for Friction Materials Manufacturing (40 CFR part 63, subpart QQQQQ) (Renewal)

OMB: 2060-0481

Document [docx]
Download: docx | pdf

SUPPORTING STATEMENT

ENVIRONMENTAL PROTECTION AGENCY

NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal)


1. Identification of the Information Collection


1(a) Title of the Information Collection


NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal), EPA ICR Number 2025.06, OMB Control Number 2060-0481.


1(b) Short Characterization/Abstract


The National Emission Standards for Hazardous Air Pollutants (NESHAP) for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ), were proposed on October 4, 2001, (66 FR 50768) and promulgated on October 18, 2002 (67 FR 64506). These regulations apply to existing facilities and new facilities. New facilities include those that commenced construction or reconstruction after the date of proposal.


A friction materials manufacturing facility is only subject to the regulation if it is a major source of hazardous air pollutant (HAP) emissions and emits, or has the potential to emit, any single HAP at a rate of 9.07 megagrams (10 tons) or more per year or any combination of HAPs at a rate of 22.68 megagrams (25 tons) or more per year. Consistent with the General Provisions (40 CFR Part 63, Subpart A), respondents do not include the owner or operator of any facility that is not a major source of HAP emissions or any facility that does not operate affected solvent mixers, even if the facility is a major source. This information is being collected to assure compliance with 40 CFR Part 63, Subpart QQQQQ.


In general, all NESHAP standards require initial notifications, performance tests, and periodic reports by the owners/operators of the affected facilities. They are also required to maintain records of the occurrence and duration of any startup, shutdown, or malfunction in the operation of an affected facility, or any period during which the monitoring system is inoperative. These notifications, reports, and records are essential in determining compliance, and are required of all affected facilities subject to NESHAP.


Any owner/operator subject to the provisions of this part shall maintain a file of these measurements, and retain the file for at least five years following the date of such measurements, maintenance reports, and records. All reports are sent to the delegated state or local authority. In the event that there is no such delegated authority, the reports are sent directly to the U.S. Environmental Protection Agency (EPA) regional office.


Approximately four respondents are currently subject to the regulation, and it is estimated that no additional respondents per year will become subject to the regulation in the next three years.


The Office of Management and Budget (OMB) approved the currently active ICR without any Terms of Clearance.


Respondents are owners or operators of each new, reconstructed, or existing affected source. The NESHAP contains an emission limitation for solvent mixers at friction materials manufacturing facilities. Solvent mixers are the affected source. Friction materials manufacturing facilities manufacture friction material using a solvent‑based process. Friction material is subsequently used to manufacture friction products that include, but are not limited to, disc brake pucks, disc brake pads, brake linings, brake shoes, brake segments, brake blocks, brake discs, clutch facings, and clutches.


There are four friction materials manufacturing facilities in the United States, which are owned and operated by the friction material manufacturing industry. None of the four facilities in the United States are owned by state, local, tribal, or the Federal government. They are owned and operated by privately owned, for-profit businesses. The “burden” to the “Affected Public” may be found below in Table 1: Annual Respondent Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal). The “burden” to the Federal Government is attributed entirely to work performed by either Federal employees or government contractors and can be found below in Table 2: Average Annual EPA Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).


2. Need for and Use of the Collection


2(a) Need/Authority for the Collection


The EPA is charged under Section 112 of the Clean Air Act, as amended, to establish standards of performance for each category or subcategory of major sources and area sources of hazardous air pollutants. These standards are applicable to new or existing sources of hazardous air pollutants and shall require the maximum degree of emission reduction. In addition, section 114(a) states that the Administrator may require any owner/operator subject to any requirement of this Act to:


(A) Establish and maintain such records; (B) make such reports; (C) install, use, and maintain such monitoring equipment, and use such audit procedures, or methods; (D) sample such emissions (in accordance with such procedures or methods, at such locations, at such intervals, during such periods, and in such manner as the Administrator shall prescribe); (E) keep records on control equipment parameters, production variables or other indirect data when direct monitoring of emissions is impractical; (F) submit compliance certifications in accordance with Section 114(a)(3); and (G) provide such other information as the Administrator may reasonably require.

In the Administrator's judgment, HAP emissions from solvent mixers either cause or contribute to air pollution that may reasonably be anticipated to endanger public health and/or welfare. Therefore, the NESHAP were promulgated for this source category at 40 CFR Part 63, Subpart QQQQQ.


2(b) Practical Utility/Users of the Data


The recordkeeping and reporting requirements in the standard ensure compliance with the applicable regulations which were promulgated in accordance with the Clean Air Act. The collected information is also used for targeting inspections and as evidence in legal proceedings.


Performance tests are required in order to determine an affected facility’s initial capability to comply with the emission standard. Continuous emission monitors are used to ensure compliance with the standard at all times. During the performance test a record of the operating parameters under which compliance was achieved may be recorded and used to determine compliance in place of a continuous emission monitor.


The notifications required in the standard are used to inform the Agency or delegated authority when a source becomes subject to the requirements of the regulations. The reviewing authority may then inspect the source to check if the pollution control devices are properly installed and operated, that leaks are being detected and repaired, and the standard is being met. The performance test may also be observed.


The required semiannual reports are used to determine periods of excess emissions, identify problems at the facility, verify operation/maintenance procedures, and for compliance determinations.


3. Non-duplication, Consultations, and Other Collection Criteria


The requested recordkeeping and reporting are required under 40 CFR Part 63, Subpart QQQQQ.


3(a) Non-duplication


If the subject standards have not been delegated, the information is sent directly to the appropriate EPA regional office. Otherwise, the information is sent directly to the delegated state or local agency. If a state or local agency has adopted its own similar standards to implement the Federal standards, a copy of the report submitted to the state or local agency can be sent to the Administrator in lieu of the report required by the Federal standards. Therefore, duplication does not exist.


3(b) Public Notice Required Prior to ICR Submission to OMB


An announcement of a public comment period for the renewal of this ICR was published in the Federal Register (79 FR 30117) on May 27, 2014. No comments were received on the burden published in the Federal Register.


3(c) Consultations


The Agency’s industry experts have been consulted, and the Agency’s internal data sources and projections of industry growth over the next three years have been considered. The primary source of information as reported by industry, in compliance with the recordkeeping and reporting provisions in the standard, is the Online Tracking Information System (OTIS) which is operated and maintained by EPA's Office of Compliance. OTIS is EPA’s database for the collection, maintenance, and retrieval of all compliance data. The growth rate for the industry is based on our consultations with the Agency’s internal industry experts.


Industry trade associations and other interested parties were provided an opportunity to comment on the burden associated with the standard as it was being developed. In developing this ICR, we contacted the Motor and Equipment Manufacturers Association (MEMA) at (202) 393-6362, and Dynax America Corporation at (540) 966-6010.


It is our policy to respond after a thorough review of comments received since the last ICR renewal, as well as to those comments submitted in response to the first Federal Register notice. In this case, no comments were received.


3(d) Effects of Less Frequent Collection


Less frequent information collection would decrease the margin of assurance that facilities are continuing to meet the standards. Requirements for information gathering and recordkeeping are useful techniques to ensure that good operation and maintenance practices are applied and emission limitations are met. If the information required by these standards was collected less frequently, the proper operation and maintenance of control equipment and the possibility of detecting violations would be less likely.


3(e) General Guidelines


These reporting or recordkeeping requirements do not violate any of the regulations promulgated by OMB under 5 CFR Part 1320, Section 1320.5.


These standards require the respondents to maintain all records, including reports and notifications for at least five years. This is consistent with the General Provisions as applied to the standards. EPA believes that the five-year records retention requirement is consistent the Part 70 permit program and the five-year statute of limitations on which the permit program is based. The retention of records for five years allows EPA to establish the compliance history of a source, any pattern of non-compliance and to determine the appropriate level of enforcement action. EPA has found that the most flagrant violators have violations extending beyond five years. In addition, EPA would be prevented from pursuing the violators due to the destruction or nonexistence of essential records.


3(f) Confidentiality


Any information submitted to the Agency, for which a claim of confidentiality is made, will be safeguarded according to the Agency policies set forth in Title 40, Chapter 1, Part 2, Subpart B - Confidentiality of Business Information (CBI) (see 40 CFR 2; 41 FR 36902, September 1, 1976; amended by 43 FR 40000, September 8, 1978; 43 FR 42251, September 20, 1978; 44 FR 17674, March 23, 1979).


3(g) Sensitive Questions


The reporting or recordkeeping requirements in the standard do not include sensitive questions.


4. The Respondents and the Information Requested


4(a) Respondents/SIC Codes


The respondents to the recordkeeping and reporting requirements are friction materials manufacturing facilities. The United States Standard Industrial Classification (SIC) codes for the respondents affected by the standards and their corresponding North American Industry Classification System (NAICS) codes are listed below.


Standard (40 CFR Part 63, Subpart QQQQQ)

SIC Codes

NAICS Codes

Motor Vehicle Brake System Manufacturing

3714

336340

All Other Miscellaneous Nonmetallic Mineral Product Manufacturing

3299

327999

Mechanical Power Transmission Equipment Manufacturing

3568

333613

4(b) Information Requested


(i) Data Items


In this ICR, all the data that is recorded or reported is required by the NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ).


A source must make the following reports:




Notifications

Initial notifications, including construction/reconstruction

63.9535(a-d), 63.05, 63.09(b)

Notification of compliance status

63.9535(e), 63.09(h)

Performance of sludge test and determine mercury emissions.

61.54(a), (c-e)



Reports

Semiannual compliance report on startup, shutdown, and malfunction

63.9540(b)(4) and (d), 63.10(d)(5)

Semiannual compliance report on no deviations

63.9540(b)(5-6)

Annual report on deviations

63.9540(c)


A source must keep the following records:



Recordkeeping

Maintain records of all reports and notifications

63.9550, 63.10(b)(1)

Maintain records for initial notification and notification of compliance status

63.9545(a)(1), 63.10(b)(xiv)

Maintain records related to startup, shutdown or malfunction

63.9545(1)(2)

Monitor records showing solvent mixers meeting the emission limitation

63.9530, 63.9545(b), 63.10(b)(2)(vi), (x-xi)


Electronic Reporting


Some of the respondents are using monitoring equipment that automatically records parameter data. Although personnel at the affected facility must still evaluate the data, internal automation has significantly reduced the burden associated with monitoring and recordkeeping at a plant site.


Also, regulatory agencies in cooperation with the respondents continue to create reporting systems to transmit data electronically. However, electronic reporting systems are still not widely used. At this time, it is estimated that approximately 10 percent of the respondents use electronic reporting.





(ii) Respondent Activities



Respondent Activities


Read instructions.


Install, calibrate, maintain, and operate solvent mixers at friction material manufacturing facility.


Write the notifications and reports listed above.


Enter information required to be recorded above.


Submit the required reports developing, acquiring, installing, and utilizing technology and systems for the purpose of collecting, validating, and verifying information.


Develop, acquire, install, and utilize technology and systems for the purpose of processing and maintaining information.


Develop, acquire, install, and utilize technology and systems for the purpose of disclosing and providing information.


Adjust the existing ways to comply with any previously applicable instructions and requirements.


Train personnel to be able to respond to a collection of information.


Transmit, or otherwise disclose the information.


Currently sources are using monitoring and reporting equipment that provide parameter data in an automated way e.g., continuous parameter monitoring system. Although personnel at the source still need to evaluate the data, this type of monitoring equipment has significantly reduced the burden associated with monitoring and recordkeeping.


5. The Information Collected: Agency Activities, Collection Methodology, and Information Management


5(a) Agency Activities


EPA conducts the following activities in connection with the acquisition, analysis, storage, and distribution of the required information:




Agency Activities


Review notifications and reports, including performance test reports, and excess emissions reports, required to be submitted by industry.


Audit facility records.


Input, analyze, and maintain data in the Online Tracking Information System (OTIS).


5(b) Collection Methodology and Management


Following notification of startup, the reviewing authority could inspect the source to determine whether the pollution control devices are properly installed and operated. Performance test reports are used by the Agency to discern a source’s initial capability to comply with the emission standard. Data and records maintained by the respondents are tabulated and published for use in compliance and enforcement programs. The semiannual reports are used for problem identification, as a check on source operation and maintenance, and for compliance determinations.


Information contained in the reports is entered into OTIS which is operated and maintained by EPA's Office of Compliance. OTIS is EPA’s database for the collection, maintenance, and retrieval of compliance data for approximately 125,000 industrial and government-owned facilities. EPA uses the OTIS for tracking air pollution compliance and enforcement by local and state regulatory agencies, EPA regional offices and EPA headquarters. EPA and its delegated Authorities can edit, store, retrieve and analyze the data.


The records required by this regulation must be retained by the owner/operator for five years.


5(c) Small Entity Flexibility


The majority of the respondents are large entities (i.e., large businesses). However, the impact on small entities (i.e., small businesses) was taken into consideration during the development of the regulation. Due to technical considerations involving the process operations and the types of control equipment employed, the recordkeeping and reporting requirements are the same for both small and large entities. The EPA considers these to be the minimum requirements needed to ensure compliance and, therefore, cannot reduce them further for small entities. To the extent that larger businesses can use economies of scale to reduce their burden, the overall burden will be reduced.


5(d) Collection Schedule


The specific frequency for each information collection activity within this request is shown in below Table 1: Annual Respondent Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).


6. Estimating the Burden and Cost of the Collection


Table 1 documents the computation of individual burdens for the recordkeeping and reporting requirements applicable to the industry for the subpart included in this ICR. The individual burdens are expressed under standardized headings believed to be consistent with the concept of burden under the Paperwork Reduction Act. Where appropriate, specific tasks and major assumptions have been identified. Responses to this information collection are mandatory.


The Agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB Control Number.


6(a) Estimating Respondent Burden


The average annual burden to industry over the next three years from these record-keeping and reporting requirements is estimated to be 1,291 (Total Labor Hours from Table 1 below). These hours are based on Agency studies and background documents from the development of the regulation, Agency knowledge and experience with the NESHAP program, the previously approved ICR, and any comments received.


6(b) Estimating Respondent Costs


(i) Estimating Labor Costs

This ICR uses the following labor rates:


Managerial $128.02 ($60.98 + 110%)

Technical $101.05 ($48.12 + 110%)

Clerical $51.37 ($24.46 + 110%)


These rates are from the United States Department of Labor, Bureau of Labor Statistics, March 2014, “Table 2. Civilian Workers, by occupational and industry group.” The rates are from column 1, “Total compensation.” The rates have been increased by 110 percent to account for the benefit packages available to those employed by private industry.


(ii) Estimating Capital/Startup and Operation and Maintenance Costs

The type of industry costs associated with the information collection activities in the subject standard are both labor costs, which are addressed elsewhere in this ICR, and the costs associated with continuous monitoring. The capital/startup costs are one-time costs when a facility becomes subject to the regulation. The annual operation and maintenance costs are the ongoing costs to maintain the monitor and other costs such as photocopying and postage.


(iii) Capital/Startup vs. Operation and Maintenance (O&M) Costs



Capital/Startup vs. Operation and Maintenance (O&M) Costs


(A)

Continuous Monitoring Device


(B)

Capital/Startup Cost for One Respondent


(C)

Number of New Respondents


(D)

Total Capital/Startup Cost, (B X C)


(E)

Annual O&M Costs for One Respondent


(F)

Number of Respondents with O&M


(G)

Total O&M,

(E X F)

Monitoring Control Device

$2,139

0

$0

$272

4

$1,088

The total capital/startup costs for this ICR are $0. This is the total of column D in the above table.


The total operation and maintenance (O&M) costs for this ICR are $1,088. This is the total of column G.


The average annual cost for capital/startup and operation and maintenance costs to industry over the next three years of the ICR is estimated to be $1,088. These are recordkeeping costs.


6(c) Estimating Agency Burden and Cost


The only costs to the Agency are those costs associated with analysis of the reported information. EPA's overall compliance and enforcement program includes activities such as the examination of records maintained by the respondents, periodic inspection of sources of emissions, and the publication and distribution of collected information.


The average annual Agency cost during the three years of the ICR is estimated to be $2,680.


This cost is based on the average hourly labor rate as follows:


Managerial $62.90 (GS-13, Step 5, $39.31 + 60%)

Technical $46.67 (GS-12, Step 1, $29.17 + 60%)

Clerical $25.25 (GS-6, Step 3, $15.78 + 60%)


These rates are from the Office of Personnel Management (OPM), 2014 General Schedule, which excludes locality rates of pay. The rates have been increased by 60 percent to account for the benefit packages available to government employees. Details upon which this estimate is based appear below in Table 2: Average Annual EPA Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).


6(d) Estimating the Respondent Universe and Total Burden and Costs


Based on our research for this ICR, on average over the next three years, approximately four existing respondents will be subject to the standard. It is estimated that no additional sources per year will become subject. The overall average number of respondents, as shown in the table below, is four per year.


The number of respondents is calculated using the following table that addresses the three years covered by this ICR.



Number of Respondents




Respondents That Submit Reports


Respondents That Do Not Submit Any Reports





Year


(A)

Number of New Respondents 1


(B)

Number of Existing Respondents


(C)

Number of Existing Respondents that keep records but do not submit reports


(D)

Number of Existing Respondents That Are Also New Respondents


(E)

Number of Respondents

(E=A+B+C-D)


1

0

4

0

0

4


2

0

4

0

0

4


3

0

4

0

0

4


Average

0

4

0

0

4

1 New respondents include sources with constructed, reconstructed and modified affected facilities.


Column D is subtracted to avoid double-counting respondents. As shown above, the average Number of Respondents over the three year period of this ICR is four.


The total number of annual responses per year is calculated using the following table:



Total Annual Responses


(A)


Information Collection Activity


(B)


Number of Respondents


(C)


Number of Responses


(D)

Number of Existing Respondents That Keep Records But Do Not Submit Reports


(E)

Total Annual Responses

E=(BxC)+D

Notification of applicability

0

1

N/A

0

Notification of construction/reconstruction

0

1

N/A

0

Notification of anticipated startup

0

1

N/A

0

Notification of actual startup

0

1

N/A

0

Notification of compliance status

0

1

N/A

0

Annual report of deviation

0.6

1

N/A

0.6

Semiannual report with no deviation

3.4

2

N/A

6.8

Unplanned startup, shutdown, malfunction report

0.4

2

N/A

0.8




Total (rounded)

8


The number of Total Annual Responses is eight.


The total annual labor costs are $126,414. Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).


6(e) Bottom Line Burden Hours and Cost Tables


The detailed bottom line burden hours and cost calculations for the respondents and the Agency are shown in Tables 1 and 2 below, respectively, and summarized below.


(i) Respondent Tally


The total annual labor hours are 1,291. Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).


Furthermore, the annual public reporting and recordkeeping burden for this collection of information is estimated to average 162 hours per response.


The total annual capital/startup and O&M costs to the regulated entity are $1,088. The cost calculations are detailed in Section 6(b)(iii), Capital/Startup vs. Operation and Maintenance (O&M) Costs.


(ii) The Agency Tally


The average annual Agency burden and cost over next three years is estimated to be 59 labor hours at a cost of $2,680. See below Table 2: Average Annual EPA Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal).



6(f) Reasons for Change in Burden


There is a small decrease in the total estimated burden as currently identified in the OMB Inventory of Approved Burdens. This decrease is due to a discrepancy identified in the previous ICR. The previous ICR assumed all existing plants transmit one-time notifications, a burden item that applies to new sources only. Since no new sources are expected over the next three-year period of the ICR, the ICR was revised to remove this burden, which resulted in a decrease in burden hours.


There is also an increase in the estimated burden cost due to the use of updated labor rates. This ICR references the most recent labor rates available from the Bureau of Labor Statistics and OPM to calculate burden costs.


6(g) Burden Statement


The annual public reporting and recordkeeping burden for this collection of information is estimated to average 162 hours per response. Burden means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.


An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a valid OMB Control Number. The OMB Control Numbers for EPA regulations are listed at 40 CFR Part 9 and 48 CFR Chapter 15.


To comment on the Agency's need for this information, the accuracy of the provided burden estimates, and any suggested methods for minimizing respondent burden, including the use of automated collection techniques, EPA has established a public docket for this ICR under Docket ID Number EPA-HQ-OECA-2014-0085. An electronic version of the public docket is available at http://www.regulations.gov/, which may be used to obtain a copy of the draft collection of information, submit or view public comments, access the index listing of the contents of the docket, and to access those documents in the public docket that are available electronically. When in the system, select “search,” then key in the docket ID number identified in this document. The documents are also available for public viewing at the Enforcement and Compliance Docket and Information Center in the EPA Docket Center (EPA/DC), EPA West, Room 3334, 1301 Constitution Ave., NW, Washington, DC. The EPA Docket Center Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number for the Reading Room is (202) 566-1744, and the telephone number for the docket center is (202) 566-1752. Also, you can send comments to the Office of Information and Regulatory Affairs, Office of Management and Budget, 725 17th Street, NW, Washington, DC 20503, Attention: Desk Officer for EPA. Please include the EPA Docket ID Number EPA-HQ-OECA-2014-0085 and OMB Control Number 2060-0481 in any correspondence.


Part B of the Supporting Statement


This part is not applicable because no statistical methods were used in collecting this information.

Table 1: Annual Respondent Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal)


Burden item

(A)

Person hours per occurrence

(B)

No. of occurrences per respondent per year

(C)

Person hours per respondent per year

(C=AxB)

(D)

Respondents per year a

(E)

Technical person- hours

per year

(E=CxD)

(F)

Management person hours per year

(Ex0.05)

(G)

Clerical person hours per year

(Ex0.1)

(H)

Cost, $ b

1. Applications

N/A








2. Survey and Studies

N/A








3. Acquisition, installation and utilization of technology and systems

54

1

54

0

0

0

0

$0

4. Reporting requirements









A. Read instructions

0.5

1

0.5

0

0

0

0

$0

B. Required activities









Startup, shutdown, malfunction plan

32

1

32

0

0

0

0

$0

C. Create information

See 4B








D. Gather existing information

See 4E








E. Write Report









Notification of applicability

2

1

2

0

0

0

0

$0

Notification of construction/reconstruction

2

1

2

0

0

0

0

$0

Notification of anticipated startup

2

1

2

0

0

0

0

$0

Notification of actual startup

2

1

2

0

0

0

0

$0

Notification of compliance status

4

1

4

0

0

0

0

$0

Annual report of deviation c

8

1

8

0.6

4.8

0.24

0.48

$540.42

Semiannual report of no deviation d

8

2

16

3.4

54.4

2.72

5.44

$6,124.79

Startup, shutdown, malfunction report e

8

2

16

0.4

6.4

0.32

0.64

$720.56

Subtotal for Reporting Requirements

75

$7,386

5. Recordkeeping requirements









A. Read instructions

4

1

4

0

0

0

0

$0

B. Plan activities

See 5E








C. Implement activities

See 5E








D. Develop record system

See 5E








E. Time to enter information









Records of solvent weight measurements f

0.033

2,600

85.8

4

343.2

17.16

34.32

$38,640.2

Records of block average solvent weight g

2

52

104

4

416

20.8

41.6

$46,836.61

Records of startup, shutdown, malfunction g

1

52

52

4

208

10.4

20.8

$23,418.30

Copies of notifications/reports h

0.25

5

1.25

4

5

0.25

0.5

$562.94

F. Time to train personnel i

20

1

20

4

80

4

8

$9,007.04

G. Time to transmit or disclose information h

0.25

5

1.25

4

5

0.25

0.5

$562.94

H. Time to audit

N/A








Subtotals for Recordkeeping Requirements

1,216

$119,028

TOTAL LABOR BURDEN AND COST (rounded)

1,291

$126,414


Assumptions:

a We have assumed that there are 4 existing sources, and that no additional new or reconstructed sources will become subject to the rule over the next three years. Within those four existing sources, there is a total of seven existing solvent mixers for an average of 1.75 mixers per source (7/4=1.75), with no additional new or reconstructed solvent mixers expected to be constructed over the three-years of the ICR.

b This ICR uses the following labor rates: $128.02 per hour for Executive, Administrative, and Managerial labor; $101.05 per hour for Technical labor, and $51.37 per hour for Clerical labor. These rates are from the United States Department of Labor, Bureau of Labor Statistics, March 2014, Table 2. Civilian Workers, by Occupational and Industry group. The rates are from column 1, Total Compensation. The rates have been increased by 110 percent to account for the benefit packages available to those employed by private industry.

c We have assumed that 15 percent of respondents will report deviation.

d We have assumed that 85 percent of respondents will report no deviation.

e We have assumed that 10 percent of respondents will have a startup, shutdown, or malfunction occur that is not managed according to the regulation.

f We have assumed that solvent weights are recorded once per hour (2 minutes [0.033 hr] per record) for 2,600 hours per year (industry average annual operating hours for solvent mixers).

g It is assumed that information would be entered once per week for 52 weeks per year.

h We have assumed that a typical plant transmits the startup, shutdown, and malfunction plan semiannually; deviation report once a year; and no deviation report semiannually for a total of five times per year.

i We have assumed that it will take 20 hours per plant once a year to train personnel.

Table 2: Average Annual EPA Burden and Cost – NESHAP for Friction Materials Manufacturing (40 CFR Part 63, Subpart QQQQQ) (Renewal)


Activity

(A)

EPA

person-hours

per occurrence

(B)

No. of occurrences per plant

per year

(C)

EPA

person- hours per plant

per year

(C=AxB)

(D)

Plants

per year a

(E)

Technical person-hours

per year

(E=CxD)

(F)

Management person-hours

per year

(Ex0.05)

(G)

Clerical person-hours

per year

(Ex0.1)

(H)

Cost,

$ b

1. Excess emissions enforcement activities c

48

1

48

0.2

9.6

0.48

0.96

$502.46

2. Report review









Notification of applicability

2

1

2

0

0

0

0

$0

Notification of construction/ reconstruction

2

1

2

0

0

0

0

$0

Notification of anticipated startup

2

1

2

0

0

0

0

$0

Notification of actual startup

2

1

2

0

0

0

0

$0

Notification of compliance status

40

1

40

0

0

0

0

$0

Annual report of deviation d

20

1

20

0.6

12

0.6

1.2

$628.08

Semiannual report of no deviation e

2

2

4

3.4

13.6

0.68

1.36

$711.82

Startup, shutdown, malfunction report f

20

2

40

0.4

16

0.8

1.6

$837.44

TOTAL ANNUAL BURDEN AND COST (rounded)

59

$2,680


Assumptions:

a We have assumed that there are 4 existing sources, and that no additional new or reconstructed sources will become subject to the rule over the next three years. Within those four existing sources, there is a total of seven existing solvent mixers for an average of 1.75 mixers per source (7/4=1.75), with no additional new or reconstructed solvent mixers expected to be constructed over the three-years of the ICR.

b This cost is based on the following labor rates which have been increased by 60 percent to account for the benefit package available to government employees: $62.90 Managerial rate (GS-13, Step 5, $39.31 + 60%), $46.67 Technical rate (GS-12, Step 1, $29.17 + 60%), and $25.01 Clerical rate (GS-6, Step 3, $15.78 + 60). These rates are from the Office of Personnel Management (OPM) 2014 General Schedule which excludes locality rates of pay.

c We have assumed that 5 percent of plants will be involved in excess emissions enforcement activities.

d We have assumed that 15 percent of respondents will report deviation.

e We have assumed that 85 percent of respondents will report no deviation.

f We have assumed that 10 percent of respondents will have a startup, shutdown, or malfunction occur that is not managed according to the regulation.

File Typeapplication/vnd.openxmlformats-officedocument.wordprocessingml.document
File TitleICR Package Instructions
Authorrmarshal
File Modified0000-00-00
File Created2021-01-26

© 2024 OMB.report | Privacy Policy