Application for Registration

According to the Paperwork Reduction Act of 1995, an agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a valid OMB control number.  The valid OMB control numbers for these information collections are 0579-0213 for APHIS and 0920-0576 for CDC.  The time required to complete the information collection for APHIS ranges from 3.75 to 19.5 hours per response, and the time required to complete the information collection for CDC ranges from 4 to 31 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information.

Table of Contents

Section 1A – Entity Information 3

Section 1B – Certification of Responsibility 4

Section 1C – Entity Abstract 5

Section 2 – Responsible Official Certification of Personnel and Facility Activities 6

Section 2 – Responsible Official Certification of Personnel and Facility Activities (Continued) 7

Section 3 – Select Agents and Toxins 8

Section 4A – Laboratorians and Animal Care Staff 9

Section 4B – Support Staff 10

Section 4C – Unescorted Visitors 11

Section 5A – Entity-Wide Security Assessment and Incident Response 12

Section 5B – Entity-Wide Biosafety/Biocontainment 14

Section 5C – Entry Requirements for Federal Select Agent Program Inspectors 15

Section 6A – Building and Suite/Room Specific Security 16

Section 6A – Building and Suite/Room Specific Security (Continued) 17

Section 6B – Room/Suite Physical Information 18

Section 6B – Room/Suite Physical Information (Continued) 19

Section 7A – Principal Investigator (PI) Information and Select Agent and Toxin Locations 20

Section 7B – Strain or Serotype Designation Information 21

Section 7C – Description of Work 22

Attachment A –Work with Toxins 24

Attachment A –Work with Toxins (Continued) 25

Attachment B – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents or Toxins, Recombinant/Synthetic Nucleic Acids, or Recombinant Synthetic Organisms 26

Attachment B – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents and Toxins, Recombinant/Synthetic Nucleic Acids, or Recombinant Synthetic Organisms (Continued) 27

Attachment C – Work with Animals 28

Attachment C – Work with Animals (Continued) 29

Attachment D – Work with Plants 30

Attachment D – Work with Plants (Continued) 31

Attachment E – Work with Arthropods 32

Attachment E – Work with Arthropods (Continued) 33

Attachment F – BSL3Ag Laboratories 34

Attachment F – BSL3Ag Laboratories (Continued) 35

Attachment G – BSL4/ABSL4 Laboratories 36

Attachment G – BSL4/ABSL4 Laboratories (Continued) 37

Application for Registration for Possession, Use, and Transfer of SELECT AGENTS and Toxins (APHIS/CDC FORM 1)

FORM APPROVED OMB NO. 0579-0213 OMB NO. 0920-0576 EXP DATE XX/XX/XXXX

Section 1A – Entity Information

This submission is:

 A new registration

 An update to an existing registration

 A renewal

Date:

ENTITY INFORMATION

Entity Application Number (e.g., CDC030001):

Current Registration Number (e.g., A00000000-0000):

Entity Name:

Physical Address (NOT a post office box):

City:

State:

Zip Code:

Additional Physical Address(es):

Type of Entity:  Academic (Private)  Academic (State)  Commercial (Profit)  Government (Federal)  Government (State/Local) Private (Non-Profit)

RESPONSIBLE OFFICIAL INFORMATION

Last Name:

First Name:

DOJ Number:

Date of Birth:

Business E-mail Address:

Title (e.g., Biosafety Officer):

Tier 1 Access

Business Telephone #:

Business Fax #:

Emergency Telephone #:

Mailing Address (NOT a post office box):

City:

State:

Zip Code:

ALTERNATE RESPONSIBLE OFFICIAL INFORMATION

Last Name:

First Name:

DOJ Number:

Date of Birth:

Business E-mail Address:

Title (e.g., Biosafety Officer):

Tier 1 Access

Business Telephone #:

Business Fax #:

Emergency Telephone #:

Mailing Address (NOT a post office box):

City:

State:

Zip Code:

Last Name:

First Name:

DOJ Number:

Date of Birth:

Business E-mail Address:

Title (e.g., Biosafety Officer):

Tier 1 Access

Business Telephone #:

Business Fax #:

Emergency Telephone #:

Mailing Address (NOT a post office box):

City:

State:

Zip Code:

OWNER / CONTROLLER INFORMATION (If Applicable)

Last Name:

First Name:

DOJ Number:

Date of Birth:

Tier 1 Access

Last Name:

First Name:

DOJ Number:

Date of Birth:

Tier 1 Access

This submission is:

 A new registration

 An update to an existing registration

 A renewal

Entity Name:

Date:

Section 1B – Certification of Responsibility

I hereby certify that I have been designated as the Responsible Official or the Alternate Responsible Official(s) for the institution/organization listed above, that I am authorized to bind the institution/organization, and that the information supplied in this registration package is, to the best of my knowledge, accurate and truthful. The institution/organization listed above meets the requirements specified in 42 CFR Part 73 and/or 7 CFR Part 331 and/or 9 CFR Part 121, is equipped and capable of safely and securely handling the agent(s), and will use or transfer these agents solely for purposes authorized by 42 CFR Part 73 and/or 7 CFR Part 331 and/or 9 CFR Part 121.

I understand that submission of a false statement and/or failure to comply with the provisions of the applicable regulations (42 CFR Part 73 and/or 7 CFR Part 331 and/or 9 CFR Part 121) may result in the immediate revocation of this entity's registration, a civil penalty of up to $500,000 for each violation, and a criminal penalty and/or imprisonment up to five years for each violation. (7 USC 8401; 18 USC 175, 175B, 1001, 3559, 3571; 42 USC 262a).

Responsible Official Signature		Date		Responsible Official Name

Alternate Responsible Official Signature		Date		Alternate Responsible Official Name

Alternate Responsible Official Signature		Date		Alternate Responsible Official Name

Alternate Responsible Official Signature		Date		Alternate Responsible Official Name

Alternate Responsible Official Signature		Date		Alternate Responsible Official Name

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 1C – Entity Abstract

Provide a summary of the overall institution mission, functions, and size. This information can include a general estimated number of employees, square footage of entire campus or facility, number of laboratories, overall scope of research, and any international collaborations. Specialized areas of research, education, or expertise can be highlighted. Include a brief description of the management structure of the institution related to oversight of the select agent facility/facilities. Provide a brief summary of the select agent and toxin work at the entity including mission, function, and size. Note: information specific to select agents and toxins will be required in later sections of this application.

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 2 – Responsible Official Certification of Personnel and Facility Activities

I certify that the following requirements are in effect and contain all information required by the Select Agent regulations [7 CFR 331, 9 CFR 121, and 42 CFR 73] (initial each line):

Security, Biosafety and Incident Response

	There is a written, site-specific security plan designed according to a site-specific risk assessment that provides graded protection in accordance with the risk of the select agent and/or toxin.
	There is a written, agent-specific, and site-specific biosafety plan commensurate with the risk of the select agent and/or toxin that contains sufficient information and documentation to describe the biosafety and containment procedures.
	There is a written, site-specific incident response plan commensurate with the hazards of the select agent and/or toxin that fully describe the entity’s response procedures to include the theft, loss or release of a select agent and/or toxin, inventory discrepancies, security breaches, natural disasters and emergencies.
	The security, biosafety and incident response plans are reviewed annually and revised as necessary, including after any drill or exercise and after any incident.
	Laboratory specific drills or exercises are conducted at least annually to validate or test the effectiveness of the security, biosafety and incident response plans.

Training

Individuals with access approval, authorized visitors, and escorted personnel are provided training on safety, security, and incident response for select agents and/or toxins, as appropriate for their role, as defined in and 7 CFR 331.15, 9 CFR 121.15, and 42 CFR 73.15.

Records

	Complete records are maintained for at least 3 years that include but are not limited to:
		an accurate, current inventory for each select agent and/or toxin possessed,
		information about all entries into areas containing select agent and/or toxin, and
		a current list of all individuals that have been granted access approval.

Responsible Official Duties & APHIS/CDC Program Notification

The Responsible Official will:

	Ensure annual inspections are conducted for each laboratory and storage area where select agent and/or toxin are stored or used to assess compliance with the requirements of the select agent regulations.
	Submit an amendment for any change in circumstances to the certificate of registration, including but not limited to: adding or removing individuals, addition of a suite/room prior to use or storage of select agent and/or toxin and any changes to Responsible or Alternate Responsible Official contact information.
	Submit an amendment describing work prior to an individual or entity conducting a restricted experiment as defined in 7 CFR Part 331.13, 9 CFR Part 121.13 or 42 CFR Part 73.13.
	Ensure inventory audits are conducted as defined in 7 CFR Part 331.11, 9 CFR Part 121.11 or 42 CFR Part 73.11.
This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:

Section 2 – Responsible Official Certification of Personnel and Facility Activities (Continued)

I certify that the following requirements are in effect and contain all information required by the Select Agent regulations [7 CFR 331, 9 CFR 121, and 42 CFR 73] (initial each line):

Responsible Official Duties & APHIS/CDC Program Notification (Continued)

The Responsible Official will:

	Request authorization from the Federal Select Agent Program using APHIS/CDC Form 2 prior to inter-entity transfer of a select agent and/or toxin, as put forth within Section 16 of the Select Agent regulations.
	Upon discovery of a theft or loss, immediately notify the Federal Select Agent Program and appropriate Federal, State, or local law enforcement agencies. Immediate notification is also required upon discovery of a release of a select agent or toxin causing occupational exposure or a release of a select agent and/or toxin outside the primary barriers of the containment area. An APHIS/CDC Form 3 must be submitted to the Federal Select Agent Program within seven calendar days upon discovery of a theft, loss, or release.
	Immediately report the identification of any APHIS select agent as defined in 9 CFR 121.5, or the identification of any Tier 1 select agent and/or toxin, to the Federal Select Agent Program and other appropriate authorities when required by Federal, State, or local law. Submit APHIS/CDC Form 4 for the identification and final disposition of any select agent or toxin contained in a specimen presented for diagnosis or verification within seven calendar days of identification and/or in a specimen presented for proficiency testing within 90 calendar days of receipt of the sample.

Responsible Official Signature		Date		Responsible Official Name (Typed or Printed)

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 3 – Select Agents and Toxins

HHS Agents and Toxins (Check if possessed)	Overlap Agents and Toxins (Check if possessed)	USDA Agents and Toxins (Check if possessed)

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 4A – Laboratorians and Animal Care Staff
Tier 1 Access	Last Name	First Name	DOJ Unique Identifier Number	Date of Birth (mm/dd/yyyy)	Role	Supervising Principal Investigator
I certify that information and training on safety, security, and incident response for working with select agents and toxins has been or will be provided to the individuals listed above before they have access to select agents and toxins. Training will address the needs of the individual, the work being performed, and risks posed by the select agents and/or toxins. Annual refresher training will be provided for these individuals. Written records and the means used to verify that the individuals understood the training will be maintained for at least three years. RO/ARO Signature:_________________________________________________ Date: _______________

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 4B – Support Staff
Tier 1 Access	Last Name	First Name	DOJ Unique Identifier Number	Date of Birth (mm/dd/yyyy)	Role
I certify that information and training on safety, security, and incident response for select agents and toxins, as appropriate for their role, has been or will be provided to the individuals listed above before they have access to select agents and toxins. Training will address the needs of the individual, the work they do, and risks posed by the select agents and/or toxins. Annual refresher training will be provided for these individuals. Written records and the means used to verify that the individuals understood the training will be maintained for at least three years. RO/ARO Signature:_________________________________________________ Date: _______________

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 4C – Unescorted Visitors For guidance and instructions on Visitors, please see www.selectagents.gov
Tier 1 Access	Last Name	First Name	HOME ENTITY DOJ Unique Identifier Number	Date of Birth (mm/dd/yyyy)	Supervising Principal Investigator
I certify that information and training on safety, security, and incident response for working with select agents and toxins has been or will be provided to the individuals listed above before they have access to select agents and toxins. Training will address the needs of the individual, the work being performed, and risks posed by the select agents and/or toxins. Annual refresher training will be provided for these individuals. Written records and the means used to verify that the individuals understood the training will be maintained for at least three years. RO/ARO Signature:_________________________________________________ Date: _______________

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 5A – Entity-Wide Security Assessment and Incident Response

1.	The facility is: (check all that apply)
			Government owned		Rented/leased
			Entity owned		Shared with another entity or
			Other ______________________		program
2.	Does the entity have a security officer or other individual(s) identified to assist the RO in security matters?					Yes	No
		If yes, does the security plan contain procedures for coordination between the RO and the entity’s security professionals?				Yes	No
3.	A threat assessment has been conducted:					Yes	No
	a.	Were local law enforcement or federal agencies consulted in developing the threat assessment?				Yes	No
	b.	Has there been a break-in at the entity in the last three years?				Yes	No
	c.	Have there been any direct threats against the entity or its scientists in the last three years?				Yes	No
	d.	Have there been protests at the entity in the last three years?				Yes	No
		If yes to any of the above, describe below. Add additional sheets as needed.
4.	Insider risk assessment
	a.	As a condition of granting unescorted access, the entity, or another organization on behalf of the entity, verifies (check all that apply):
			Educational background
			Previous work references
			Criminal history (beyond the security risk assessment approved by the Federal Select Agent Program)
			Other ____________________________
			None
	b.	Does the entity have policies and procedures for self and peer reporting?				Yes	No
	c.	Does the entity have additional requirements for personnel suitability to retain access to select agents or toxins?				Yes	No
5.	Natural hazards
	a.	Is the entity located in any of the following hazard zones?
			Flood/flood zone		Earthquake (as defined by USGS)
			Hurricane		Wildfire
			Tornado		Tsunami
			Other__________________________
	b.	In the event of a natural disaster with warning, the entity will (check all that apply):
			Secure the select agent and/or toxin in place.
			Transfer the select agent and/or toxin to an alternate registered location or entity.
			Destroy the select agent and/or toxin.
			Other ____________________________

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 5A – Entity-Wide Security Assessment and Incident Response (Continued)

6.	Are there electronic records and databases that would allow access to select agent and/or toxin?			Yes	No
		If yes, indicate the means to control access by completing a-f below:
	a.	Is a stand-alone (non-networked) computer employed?		Yes	No
	b.	Are there area external connections to systems that control security of the facility (remote log in, work from home)?		Yes	No
	c.	Is access to files or equipment containing select agent and/or toxin related information granted to users only when necessary to fulfill their roles and responsibilities?		Yes	No
	d.	Is user access modified when roles and responsibilities change or when their access to select agent and/or toxin is suspended or revoked?		Yes	No
	e.	Are user-based passwords employed?		Yes	No
	f.	Are anti-virus and anti-malware programs employed?		Yes	No
7.	Shipping/Receiving
	a.	Does the entity have a centralized receiving area?		Yes	No
	b.	Are all personnel who ship or receive select agent and/or toxin shipments Security Risk Assessment (SRA) approved?		Yes	No
	c.	Are select agent and/or toxin shipments stored in a registered and secured area prior to distribution to the Principal Investigators (PIs)?		Yes	No
8.	Does the entity transport select agent and/or toxin outside of registered area(s)?			Yes	No
		If yes, does the security plan address transport of select agent and/or toxin material
		a.	through non-registered areas?	Yes	No
		b.	during intra-entity transfers using chain of custody documentation?	Yes	No
9.	Has a response time for local law, guard force or other designated responders been determined?			Yes	No
10.	Is permission required to conduct select agent and/or toxin work after established work hours?			Yes	No
		If yes, who grants permission?
			RO/ARO
			PI
			Other _________________________

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 5B – Entity-Wide Biosafety/Biocontainment

1.	Describe the program or expertise used to develop and implement the biosafety and biocontainment procedures described in the site-specific biosafety or biocontainment plan. Add additional sheets as needed.
2.	Laboratory personnel must demonstrate proficiency in laboratory procedures prior to working with select agents and/or toxins.			Yes	No
3.	Appropriate Personal Protective Equipment (PPE) for the select agent and/or toxin and the work performed is required.			Yes	No
4.	Individuals with access to Tier 1 select agent and/or toxin are enrolled in an occupational health program.			Yes	No
5.	Laboratory personnel with access to non Tier 1 select agent and/or toxin are enrolled in an occupational health program as appropriate.			Yes	No
6.	There are policies for the safe handling of sharps.			Yes	No
7.	There is a spill protocol in place appropriate to the select agent and/or toxin risk.			Yes	No
8.	There is an effective, integrated pest management program in place.			Yes	No

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 5C – Entry Requirements for Federal Select Agent Program Inspectors

1.

Describe procedures for entry to the facility, such as gate location, visitor reception area, and parking for inspectors performing a site visit. Add additional sheets as needed.

2.

Identification requirements:

Government ID

Other ID (describe) ____________________

3.

Are there security clearance requirements?

Yes

No

If yes, check all that apply.

Exchange of security clearance documentation

Describe ____________________________________________

Completion of entity specific security documentation

Describe ____________________________________________

4.

Is respiratory protection required?

Yes

No

a.

Documentation of medical clearance for respirator use required.

Yes

No

b.

List required respirators (check all that apply):

N95

N100

PAPR: If required, will the entity provide PAPRs?

Yes

No

Other ___________________

5.

List other PPE required (indicate what will be provided by the entity). Add additional sheets as needed.

6.

Medical documentation required:

Yes

No

a.

Immunizations

Yes

No

Required (specify) ________________________________________________

Recommended (specify) ___________________________________________

b.

PPD skin test (e.g. for animal clearance)

Yes

No

In past 6 months?

In the past 12 months?

7.

Is entity specific training required?

Yes

No

If yes, provide a description (including the estimated time to complete all entry training for inspectors). Add additional sheets as needed.

8.

Describe any additional entry requirements for inspectors. Add additional sheets as needed.

This submission is:

 A new registration

 An update to an existing registration

 A renewal

Entity Name:

Date:

Building/Suite or Room:

Section 6A – Building and Suite/Room Specific Security

1.

Will this suite/room be used for Tier 1 select agent and/or toxin?

Yes

No

2.

Perimeter security measures outside the building (check all that apply):

Security lighting

Bars/security film on windows

Exterior intrusion detection system

Perimeter fence

Roving guards

Video surveillance of all access points

Vehicle screening

Other ________________________

None

3.

Access to building(s) or other area(s) housing the suite/room is controlled by (check all that apply):

Lock and key

Card access system

Biometric system

Card access system w/ PIN

Other _____________________________

Guards

None

4.

Additional security measures present in the interior of the building where select agent and/or toxin is stored or used (check all that apply):

Additional locked doors

Card access system

Card access system with PIN

Biometric System

Intrusion detection system

a.

What triggers the alarm? ___________________________________

b.

Is the alarm contracted to an outside company?

Yes

No

c.

Who does the alarm notify? _________________________________

d.

Are any emergency exits equipped with the same kind of intrusion detection system as the customary entrances?

Yes

No

Video surveillance

a.

Does the video surveillance observe select agent and/or toxin work?

Yes

No

b.

Does the video surveillance observe select agent and/or toxin storage?

Yes

No

c.

Does the video surveillance observe access to the registered room?

Yes

No

d.

Is the video monitored by security personnel?

Yes

No

e.

Is the video reviewed by laboratory personnel?

Yes

No

Other _____________________________

None

This submission is:	 A new registration		 An update to an existing registration	 A renewal
Entity Name:					Date:
Building/Suite or Room:

Section 6A – Building and Suite/Room Specific Security (Continued)

5.

Access to suite/room where select agent and/or toxin is stored or used is controlled by (check all that apply):

Lock and key

Card access system

Card access system with PIN

Biometric System

Other _____________________________________________________________

6.

Access to the storage unit(s) where select agent and/or toxin are housed is controlled by (check all that apply):

No access control on the storage unit(s)

Lock and key

Card access system

Card access system with PIN

Biometric System

Other _____________________________________________________________

7.

Is there a pass through autoclave in the suite/room?

Yes

No

If yes, are the doors interlocked?

Yes

No

8.

Is an autoclave outside of the suite/room used for decontamination of select agent and/or toxin waste?

Yes

No

If yes, distance from suite/room to autoclave ___________________

9.

Is there a pass through window or box at the perimeter of the suite/room?

Yes

No

If yes, is it secured?

Yes

No

10.

Is there a dunk tank at the perimeter of the suite/room?

Yes

No

If yes, is it secured?

Yes

No

This submission is:	 A new registration		 An update to an existing registration	 A renewal
Entity Name:					Date:
Building/Suite or Room:

Section 6B – Room/Suite Physical Information

For each registered storage area, laboratory suite or room:

Include a floor plan for the suite or room where select agent and/or toxin is to be used or stored. Floor plan for each suite or room should include as applicable: points of entry and/or egress for personnel, locations of equipment [including but not limited to]: sink, eyewash, fume hood, freezer, refrigerator, floor drains, showers, incubator, centrifuge, animal caging, autoclave, Biological Safety Cabinet (BSC) including type (e.g., Class II, Type A2; Class III)], Heating Ventilation and Air Conditioning (HVAC) supply and exhaust vents, and cage washing area. A separate floor plan specifying airflow may also be requested.

For storage only area(s), proceed to Section 7.

Answer the following questions for each laboratory suite or room:

The following questions may not apply to all biosafety levels. The accompanying instructions detail which questions apply to each biosafety level according to the current edition of the Biosafety in Microbiological and Biomedical Laboratories (BMBL), the National Institutes of Health (NIH) Guidelines for Research Involving Recombinant DNA Molecules, and the American Society of Tropical Medicine and Hygiene Arthropod Containment Guidelines. If the question does not apply to the laboratory suite or room, check “No”.

1.

This laboratory is operated at (check all that apply):

BSL2

NIHBL2

NIHBL2-LS

ACL3

BSL3

NIHBL3

NIHBL3-LS

ACL4

BSL4

NIHBL4

NIHBL4-LS

ABSL2

NIHBL2N

ABSL3

NIHBL3N

BSL3Ag

NIHBL4N

ABSL4

List the resources/references used ­­­­­­­­­­­­­­­­­­­­______________________________________________________

2.

BSCs and fume hoods are certified at least annually and records kept for at least three years.

Yes

No

3.

A sink is present in the laboratory for hand washing.

Yes

No

If yes, the hand washing sink is hands-free or automatically operated.

Yes

No

4.

An eyewash station is readily available.

Yes

No

5.

Liquid effluents originating from the laboratory are collected and heat or chemically treated for sterility prior to exiting the facility or entering a public sewage system.

Yes

No

If yes,

a.

Are the liquid effluents from the containment shower areas similarly treated for sterility?

Yes

No

b.

Is the effluent decontamination system validated monthly with a bio-indicator?

Yes

No

If BSL3Ag, BSL4 or ABSL4 is selected, proceed to Section 7.

6.

Access to the laboratory is through two self-closing doors.

Yes

No

If yes, door(s) from the anteroom open inward to the laboratory?

Yes

No

This submission is:	 A new registration		 An update to an existing registration	 A renewal
Entity Name:					Date:
Building/Suite or Room:

Section 6B – Room/Suite Physical Information (Continued)

7.	The ventilation system provides sustained directional airflow by drawing air into the laboratory from “clean” areas toward “potentially contaminated” areas.			Yes	No
8.	The laboratory is designed such that under failure conditions the airflow will not be reversed.			Yes	No
9.	Laboratory design and operational parameters are re-verified at least annually.			Yes	No
10.	A visual monitoring device, which confirms directional airflow, is provided at the laboratory entry.			Yes	No
11.	Laboratory exhaust is not re-circulated to other areas of the building.			Yes	No
12.	Exhaust air is HEPA filtered.			Yes	No
	a.	If yes, the HEPA filter housing has decontamination and test ports.		Yes	No
		i.	If this laboratory is a suite, please list rooms with HEPA filtered exhaust : __________________
		ii.	HEPA filters and housings are certified at least annually.	Yes	No
	b.	If no, exhaust air is dispersed away from occupied areas and building air intake locations.		Yes	No
13.	Emergency shower is readily available.			Yes	No
14.	Floor drains are present.			Yes	No
15.	Sink traps and any floor drains are filled with water and/or appropriate liquid to prevent the migration of vermin and gases.			Yes	No
16.	Mechanical cage washer is present.			Yes	No
		If yes, cage washer has a final rinse temperature of at least 180°F.		Yes	No
17.	The laboratory has a shower-out capability with a change room.			Yes	No

This submission is:	 A new registration	 An update to an existing registration	 A renewal
Entity Name:				Date:

Section 7A – Principal Investigator (PI) Information and Select Agent and Toxin Locations

A complete Section 7 must be submitted for each PI. If separate PI’s would result in an identical Section 7 being completed, multiple PI’s can be listed in the header.

PI	Last Name:	First Name:	DOJ Number:
			Date of Birth:
			Tier 1 Access

Select Agent/Toxin/Regulated Nucleic Acid	Location		Laboratory or Storage (Select one or both)		Laboratory Safety Level (Leave blank if storage only)
	Bldg	Suite/Room	Lab	Storage

Suite Legend: (If Applicable)

Suite A = Rooms 1, 2, 3, 4

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Section 7B – Strain or Serotype Designation Information

Select Agent/Toxin/ Regulated Nucleic Acid	Strain or Serotype Designations
Agent
Toxin
Regulated Nucleic Acid

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Section 7C – Description of Work

1.

Provide the objectives of work for each select agent and/or toxin listed in Section 7A by agent/toxin and containment level(s), including a description of the methodologies or laboratory procedures that will be used. Include any work involving animals, arthropods or plants. Attachments A-G must be completed if appropriate for the work described. If no work is being performed with select agent and/or toxin, indicate “storage only”. Attach additional sheets as needed.

Agent/Toxin	BSL	Objective of Work

.

2.	Provide an estimate of the maximum quantities (e.g., number of Petri dishes or total volume of liquid media) and concentration of each organism grown at a given time (e.g., 2 - 250 ml flasks of 105 cfu/ml). If select agent will not be propagated, indicate “no propagation of agent”. Attach additional sheets if needed.
Agent		Maximum Quantity/Concentration

3.	Provide an estimate of the maximum quantity of functional toxin held by the PI at any one time (e.g., 500 mg, 100 ml x 100 ug/ul). Attach additional sheets if needed.
Toxin			Maximum Quantity
4.	Equipment that may produce infectious agent or toxin aerosols (e.g., ultracentrifuge, flow cytometer, cell sorter, plate washer) is contained in primary barrier devices that exhaust air through HEPA filtration or other equivalent technology before being discharged into the laboratory.			Yes	No
5.	Name(s) of Individual(s) responsible for inventory of select agent(s) and/or toxin(s):
	Inventory record is reconciled:  Annually  Other (specify frequency)_____________
6.	Regulated nucleic acids as defined in 7 CFR 331.3, 9 CFR 121.3, 42 CFR 73.3 or 42 CFR 73.4 are held in long-term storage.			Yes	No

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Section 7C – Description of Work (Continued)

7.	All cultures, stocks and other regulated wastes are decontaminated prior to disposal.		Yes	No
	If yes, describe method:
		Autoclaved
		Chemical (disinfectant, concentration, and time) ___________________________________________
		Incineration
		Irradiation
		Other ______________________________________________________________________________
8.	Written records that would allow someone the ability to gain access to select agent and/or toxin are controlled by:
		Lock and key
		Locked filing cabinet, drawer, cabinet, etc.
		Card access system
		Other _______________________________________________________________

9.	Will work be performed with:
	a.	toxins or with agents that will be propagated and produce regulated amounts of toxins?	Yes	No
		If yes, complete Attachment A – Work With Toxins
	b.	regulated nucleic acids, genetic modification of select agents or toxins, recombinant/synthetic nucleic acids or recombinant/synthetic organisms?	Yes	No
		If yes, complete Attachment 2 – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents or Toxins, Recombinant/Synthetic Nucleic Acids or Recombinant/Synthetic Organisms
	c.	animals?	Yes	No
		If yes, complete Attachment C – Work with Animals
	d.	plants?	Yes	No
		If yes, complete Attachment D – Work with Plants
	e.	arthropods?	Yes	No
		If yes, complete Attachment E – Work with Arthropods
10.	Will work be performed in:
	a.	BSL3Ag laboratory?	Yes	No
		If yes, complete Attachment F – BSL3Ag Laboratories
	b.	BSL4/ABSL4 laboratory?	Yes	No
		If yes, complete Attachment G – BSL4/ABSL4 Laboratories

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment A –Work with Toxins

1.	A toxin-specific Chemical Hygiene Plan is available for the laboratory using select toxins.				Yes	No
2.	Select toxin manipulation or production in the laboratory includes (check all that apply):
		Dry forms
		Liquid forms
		Centrifugation
		Pressure filtration systems (e.g., chromatography)
3.	Animals are exposed to select toxins.				Yes	No
	a.	If yes, toxin exposure procedure(s) is performed in registered laboratories.			Yes	No
	b.	If yes, complete relevant questions in Attachment C - Work with Animals.
4.	Select toxin is produced by PI(s).				Yes	No
		If yes, provide a brief description of the method and an estimate of the maximum quantities during production, purification, and concentration. Add additional sheets as needed.
5.	A hazard sign is posted when select toxins are in use.				Yes	No
6.	All select toxins, cultures, stock, materials coming into contact with toxins, and other regulated wastes are appropriately inactivated prior to disposal.				Yes	No
		If yes, describe method:
			Autoclaved
			Chemical (disinfectant, concentration, and time) __________________________________
			Incineration
			Other ___________________________________________________________________
7.	Dilution procedures and other manipulations of concentrated select toxins are performed.				Yes	No
		If yes, conducted in:
			Fume hood
			Biological Safety Cabinet (BSC)
			Outside of a BSC or fume hood
			Work is conducted with two knowledgeable people present.
8.	Select toxins are transferred (intra-entity transfer) to other individuals at the entity outside of the laboratory producing or receiving the toxin (check all that apply):				Yes	No
	If yes, indicate below:
		Above the aggregate amount
		Below the aggregate amount
9.	Select toxins are transferred to other entities in quantities below the aggregate amount (inter-entity transfer).				Yes	No

This submission is:		 A new registration	 An update to an existing registration		 A Renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment A –Work with Toxins (Continued)

10.	Select toxins are commercially distributed/shipped outside of the laboratory producing the toxin.					Yes	No
			If yes, is there a hazard communication plan?			Yes	No
11.		Will work involve possession, use or transfer of recombinant and/or synthetic nucleic acids that encode for the functional form(s) of any select toxins as defined in 42 CFR 73.3 or 42 CFR 73.13?				Yes	No
				If yes, complete Attachment 2 – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents and Toxins, Recombinant/Synthetic Nucleic Acids or Recombinant/Synthetic Organisms.

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment B – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents or Toxins, Recombinant/Synthetic Nucleic Acids, or Recombinant Synthetic Organisms

1.	Will work involve possession, use, or transfer of the following?
	a.	Nucleic acids that can produce infectious forms of select agent viruses.			Yes	No
	b.	Recombinant and/or synthetic nucleic acids that encode for the functional form(s) of any select toxins if the nucleic acids (i) can be expressed in vivo or in vitro or (ii) are in a vector or recombinant host genome and can be expressed in vivo or in vitro.			Yes	No
	c.	Select agent viruses, bacteria, fungi or toxins that have been genetically modified.			Yes	No
2.	Will work involve the following with select agents and/or toxins:
	a.	Introduction and/or modification of genetic elements.			Yes	No
	b.	Recombinant or synthetic nucleic acids.			Yes	No
	c.	Recombinant or synthetic organisms.			Yes		No
	d.	Reverse genetics system to produce infectious forms of select agent viruses, or any complete set of reagents that would allow rescue of infectious virus available for use by a PI at the entity.			Yes		No
3.	Will a restricted experiment be performed as defined in 42 CFR 73.13, 7 CFR 331.13 or 9 CFR 121.13?				Yes	No
	a.	If yes, please indicate the type of restricted experiment:
			The introduction of, or selection for, drug resistance trait(s) into select agent organisms.
			List the agent(s) and the drug resistance trait(s):
			Select Agent ______________________	Drug Resistance Trait ______________
			Select Agent ______________________	Drug Resistance Trait ______________
			Select Agent ______________________	Drug Resistance Trait ______________
			The deliberate formation of DNA containing genes for the biosynthesis of toxin lethal for vertebrates at an LD50 < 100 ng/kg body weight. List toxins _________________________________________________
	b.	Has this PI received approval from the APHIS Administrator or HHS Secretary for this restricted experiment?			Yes	No
4.	Will work involve possession, use or transfer of a product of a restricted experiment?				Yes	No
	a.	If yes, please indicate the type of restricted experiment product:
			Drug resistance trait(s) in select agent organisms.
			List the select agent(s) and the drug resistance trait(s) _______________________
			DNA containing genes for the biosynthesis of toxin lethal for vertebrates at an LD50 < 100 ng/kg body weight.
			List toxin(s) ____________________________________________________
	b.	Has this PI received approval from the APHIS Administrator or HHS Secretary for this product of a restricted experiment?			Yes	No
5.	Will experiments involve the acquisition of increased/restored virulence (e.g., drug resistance, increased host range, enhanced transmissibility, infectivity, environmental stability) in select agents or toxins?				Yes	No

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment B – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents and Toxins, Recombinant/Synthetic Nucleic Acids, or Recombinant Synthetic Organisms (Continued)

6.	For any question 1-5 above answered “yes”, provide a brief description of the work. Add additional sheets as needed.
7.	An Institutional Biosafety Committee (IBC) reviews and approves protocols to perform recombinant work with select agents and toxins at this facility.			Yes	No
			If yes, has the IBC approved the work described above?	Yes	No
			If no, please provide an explanation. Add additional sheets as needed.

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment C – Work with Animals

1.	Provide the select agent/toxin and species of animal to be used:
Select Agent / Toxin					Species of Animal	Route(s) of Administration
2.	Are animals exposed to select agents or toxins by the aerosol route?						Yes		No
		If yes, is the aerosol exposure equipment used within a primary containment device?					Yes		No
3.	Describe the waste stream:
	a.	Are animal carcasses, cages, and waste (e.g., sewage, bedding) treated prior to disposal by an approved method? (check all that apply):					Yes		No
			Autoclaved. Describe validation procedures that account for variables such as time and temperature of autoclave run cycles, as well as temperature and weight of carcass at initiation of autoclave cycle. Add additional sheets as needed.
			Chemical (disinfectant, concentration, and time) _______________________________________
			Incineration
			Tissue Digester
			Other ________________________________________________________________________
	b.	Waste Handling Procedures
				Waste decontaminated inside the containment area (e.g., pass-through autoclave loaded within the animal facility).
				Waste outside of the containment area for decontamination. Describe when and how waste is treated before transport out of the containment area. Add additional sheets as needed.
4.	Describe any inactivation (e.g., formalin fixation, lysis of cells for nucleic acid extraction, irradiation) of samples collected from infected animals that will be manipulated at a lower biosafety level. Include concentration or dosage and contact/exposure time, as applicable. Add additional sheets as needed.
5.	The entity requires that an Institutional Animal Care and Use Committee (IACUC) review and approve protocols prior to work with animals at this entity.						Yes		No
		If yes, the proposed work with select agents and toxins in animals has been approved by the IACUC. If no, explain. Add additional sheets as needed.					Yes		No

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment C – Work with Animals (Continued)

6.	The laboratory is accredited by the Association for Assessment and Accreditation of Laboratory Animal Care (AAALAC).			Yes	No
		If yes, give most recent (re)accreditation date ____________________
7.	There is a system in place for recording the number of animals infected, the number of animals disposed of, and the records are reviewed frequently.			Yes	No
		If yes, describe. Add additional sheets as needed.
8.	Are animals restrained for experimental manipulation? Yes No
		If no, explain.
9.	Are experimentally infected animals monitored (e.g., daily checks)? Yes No
		If no, explain.
10.	Describe animal housing for each species, including whether cages provide primary containment and a brief description (e.g. cage or cage rack is HEPA filtered, active or passive ventilation of the cages, non-containment caging housed within inward flow ventilated enclosure).
	Species		Animal Housing
11.	Describe how animals will be euthanized. Add additional sheets as needed.
12.	Are animals euthanized?			Yes	No
		If no, explain.
13.	Describe how animal carcasses are secured prior to decontamination.
		Locked freezers, coolers
		Not secured, immediately decontaminated (e.g., autoclave, tissue digester, incinerator)
		Other _____________________________________________________

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment D – Work with Plants

1.	Provide the select agent and species of plant to be used:
Select Agent				Species of Plant	Route(s) of Inoculation
2.	Plant waste is treated prior to disposal (e.g., soil, plant material, materials accompanying plants or samples) by an approved method (check all that apply):					Yes	No
		Autoclaved
		Chemical (disinfectant, concentration, and time) ___________________________________
		Irradiation
		Incineration
		Other ________________________________
3.	Are vectors present?					Yes	No
	a.	Vectors are restricted to cages?				Yes	No
	b.	Are adjacent areas monitored to observe potential escapes?				Yes	No
	c.	Please describe vector species and cage mesh size __________________________
	d.	Are vectors exposed to select agents or plants infected with select agents?				Yes	No
			If yes, complete Attachment E - Work with Arthropods.
4.	Will plants exposed to select agents be housed or manipulated in a glass house?					Yes	No
	a.	Is the glass house attached to the laboratory?				Yes	No
	b.	Is the glass house separated from the laboratory?				Yes	No
	c.	Is pest monitoring conducted within the glass house?				Yes	No
	d.	Are inoculated plants moved between areas such as glass house to laboratory?				Yes	No
	e.	Structure is reinforced.				Yes	No
	f.	Floor is constructed of:
			Concrete
			Tile or other floor covering
			Dirt or gravel
5.	Will plants exposed to select agents be housed or manipulated in a greenhouse?					Yes	No
	a.	Is the greenhouse attached to the laboratory?				Yes	No
	b.	Is the greenhouse separated from the laboratory?				Yes	No
	c.	Is pest monitoring conducted within the greenhouse?				Yes	No
	d.	Are inoculated plants moved between areas such as greenhouse to laboratory?				Yes	No
	e.	Structure is reinforced.				Yes	No
	f.	Floor is constructed of:
			Concrete
			Tile or other floor covering
			Dirt or gravel

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment D – Work with Plants (Continued)

6.	Will plants exposed to select agents be housed or manipulated in a screenhouse?			Yes	No
	a.	Is the screenhouse attached to the laboratory?		Yes	No
	b.	Is the screenhouse separated from the laboratory?		Yes	No
	c.	Is pest monitoring conducted within the screenhouse?		Yes	No
	d.	Are inoculated plants moved between areas such as screenhouse to laboratory?		Yes	No
	e.	If yes, provide a description of the screenhouse materials (including screen mesh size)_______________________________________________________________
	f.	Structure is reinforced.		Yes	No
	g.	Floor is constructed of:
			Concrete
			Tile or other floor covering
			Dirt or gravel
7.	Will plants exposed to select agents be housed or manipulated in a growth chamber?			Yes	No
	a.	Is the growth chamber located in or attached to the laboratory?		Yes	No
	b.	Is the growth chamber separated from the laboratory?		Yes	No
	c.	Is pest monitoring conducted within the growth chamber?		Yes	No
	d.	Are inoculated plants moved between areas such as growth chamber to laboratory?		Yes	No
	f.	Structure is reinforced.		Yes	No
	g.	Floor is constructed of:
			Concrete
			Tile or other floor covering
			Dirt or gravel
	h.	Manufacturer name _____________________ Model number __________________
	i.	Access to growth chamber is controlled (e.g., lock and key, card access system, biometrics).		Yes	No
	j.	Is the growth chamber located at a reasonable distance from other growth chambers with healthy plants, insectaries and outside doors?		Yes	No
8.	Will work be performed with regulated nucleic acids, genetic modification of select agents or toxins, recombinant/synthetic nucleic acids or recombinant/synthetic organisms?			Yes	No
		If yes, complete Attachment B – Work with Regulated Nucleic Acids, Genetic Modification of Select Agents or Toxins, Recombinant/Synthetic Nucleic Acids or Recombinant/Synthetic Organisms.

This submission is:		 A new registration	 An update to an existing registration		 A renewal
Entity Name:						Date:
PI(s):				Laboratory Safety Level:

Attachment E – Work with Arthropods

1.

Work is performed with field-collected arthropods in a diagnostic capacity only for identification of select agents.

Yes

No

2.

Work is performed to experimentally inoculate or infect arthropods (any stages) with select agents.

Yes

No

If yes, complete questions 3-16.

3.

Provide the select agent and species of arthropod used:

Select Agent

Species of Arthropod

4.

Arthropod experimental exposure route(s).

a.

Injected with select agent.

Yes

No

b.

Infected with select agent via blood meal.

Yes

No

If yes, indicate the blood meal source.

Animal species ___________________________________

If vertebrate hosts are used, has the IACUC approved the work proposed in this objective of work?

Yes

No

If yes, complete Attachment C - Work with Animals.

If no, explain. Add additional sheets as needed.

Collected blood (describe type/method) ______________________________

c.

Infected with select agent via insect feeding on select agent infected plants.

Yes

No

If yes, complete Attachment D - Work with Plants.

d.

Other (Describe) _____________________________________________________

5.

Provide a description of the procedures used for primary containment and any transfer(s) of infected arthropods. Add additional sheets as needed.

6.

There is a system in place for recording the number of arthropods infected and the number of arthropods disposed of, and the records are reviewed frequently.

Yes

No

If yes, describe. Add additional sheets as needed.

7.

Arthropod containment laboratory design and operational procedures are developed and implemented in accordance with guidance found in the current edition of the Arthropod Containment Guidelines, a project of the American Committee of Medical Entomology of the American Society of Tropical Medicine and Hygiene.

Yes

No

This submission is:

 A new registration

 An update to an existing registration

 A renewal

Entity Name:

Date:

PI(s):

Laboratory Safety Level:

Attachment E – Work with Arthropods (Continued)

8.	An Institutional Biosafety Committee (IBC) reviews and approves arthropod work with select agents at this facility.			Yes		No
	If yes,
	a.	has the IBC approved the arthropod containment laboratory design and operational procedures?		Yes		No
	b.	has the IBC approved the work described in this objective of work?		Yes		No
	If no, explain. Add additional sheets as necessary.
9.	Arthropods are prevented from release into suite/room.			Yes		No
		If yes, do procedures include protocol for accidental escape?		Yes		No
10.	Experimentally infected arthropods are housed and manipulated in a suite/room such that accidental contact and release is prevented.			Yes		No
11.	Ventilation filters/barriers are installed to prevent arthropod escape.			Yes		No
12.	Floor drains are present in the laboratory.			Yes		No
		If yes, floor drains are modified to prevent accidental release of arthropods and agents.		Yes		No
13.	Suite/room plumbing is suitable to prevent arthropod escape.			Yes		No
14.	All stages of arthropods are killed before disposal.			Yes		No
15.	All wastes from the arthropod containment laboratory are treated for disposal using an approved method.				Yes	No
		If yes, describe method:
			Autoclaved
			Chemical (disinfectant, concentration, and time) _________________________________
			Incineration
			Other ___________________________________________________________________
16.	Animals or plants are permitted in the arthropod containment laboratory.				Yes	No
	If yes,
	a.	are animals or plants associated with the work being performed?			Yes	No
	b.	are animals or plants accessible to escaped arthropods?			Yes	No

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Attachment F – BSL3Ag Laboratories

1.		Supplies, material and equipment enter and exit BSL3Ag areas only through an airlock, fumigation chamber, an interlocked and double-door autoclave, or shower.		Yes		No
			For materials which are temperature sensitive, a gas sterilizer, pass-through liquid dunk tank, or a cold gas decontamination chamber are provided.	Yes		No
2.		Is a shower required when leaving the containment boundary		Yes		No
3.		Disposable materials are decontaminated by a verified method (check all that apply):		Yes		No
			Autoclaved
			Chemical (disinfectant, concentration, and time) _____________________________
			Incineration __________________________________________________________
			Other _______________________________________________________________
4.		All containment areas are designed, constructed and verified to function as a primary containment barrier. All walls are constructed slab-to-slab and walls, floors, and ceilings are sealed. All penetrations into the laboratory are sealed airtight to prevent escape of agents and to allow fumigation for biological decontamination.		Yes		No
5.		Differential pressures/directional airflow are monitored and alarmed to indicate system failure.		Yes		No
6.		There is HEPA filtration of all supply and exhaust air to and from the containment space.		Yes		No
			If yes, all HEPA filters are certified annually.	Yes		No
7.		Laboratory procedure and design features include:
		a.	Personnel ingress and egress only through a series of rooms which includes a ventilated vestibule.	Yes		No
		b.	A clean change room outside of containment.	Yes		No
		c.	Doors that define a containment boundary have compressible or inflatable gaskets with airtight hinges and latch/knob areas.	Yes		No
		d.	A shower room at the non-containment/containment boundary.	Yes		No
		e.	A dirty change room within containment.	Yes		No
8.	A second shower is required at the facility access control point before donning street clothing.				Yes	No

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Attachment F – BSL3Ag Laboratories (Continued)

9.	Humane restraining devices are provided in large animal rooms.		Yes	No
	If yes, describe. Add additional sheets as needed.
10.	Necropsy rooms are sized and equipped to accommodate large animals.		Yes	No
	If yes, describe. Add additional sheets as needed.

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Attachment G – BSL4/ABSL4 Laboratories

BSL4 Laboratory

1.	Will work be performed in a BSL4/ABSL4 Cabinet Laboratory?		Yes	No
		If yes, complete questions 2 - 8

2.	Describe the type of personal protective equipment that will be used. Add additional sheets as needed.

3.	Describe the decontamination methods for materials/equipment in the Class III cabinet. Add additional sheets as needed.

4.	Describe what liquid effluents are decontaminated and how they are decontaminated. Add additional sheets as needed.

5.	Describe the supply and exhaust components of the ventilation system, including how the ventilation system of the Class III cabinet is manifolded to the room ventilation. Add additional sheets as needed.

6.	In the event of a ventilation failure, describe what measures are used to prevent reversal of airflow. Add additional sheets as needed.

7.	Describe how differential pressures and directional airflow are monitored and analyzed. Add additional sheets as needed.

8.	Describe how containment parameters are monitored daily. Add additional sheets as needed.

9.	Will work be performed in a BSL4/ABSL4 Suit Laboratory?		Yes	No
		If yes, complete questions 10 - 16

10.	Describe the type of personal protective equipment that will be used. Add additional sheets as needed.

11.	Describe what liquid effluents are decontaminated and what measures are used to do so. Add additional sheets as needed.

This submission is:		 A new registration	 An update to an existing registration	 A renewal
Entity Name:					Date:
PI(s):

Attachment G – BSL4/ABSL4 Laboratories (Continued)

12.	Describe the supply and exhaust components of the ventilation system, including how negative pressure is maintained and HEPA filtration of supply and exhaust air. Add additional sheets as needed.

13.	In the event of a ventilation failure, describe what measures are used to prevent reversal of airflow. Add additional sheets as needed.

14.	Describe how differential pressures and directional airflow are monitored and analyzed. Add additional sheets as needed.

15.	In the event of a breathing air failure, describe what facility redundancies are in place. Add additional sheets as needed.

16.	Describe how containment parameters are monitored daily. Add additional sheets as needed.