5900-80 Emission Unit Description for Combustion Sources (EUD1)

OMB No. 2060-0336,

Approval Expires: MM/DD/YYYY

Federal Operating Permit Program (40 CFR Part 71)

EMISSION UNIT DESCRIPTION FOR FUEL COMBUSTION SOURCES (EUD-1)

A. General Information

Emissions unit ID ___________ Description__________________________________

SIC Code (4-digit) __________ SCC Code________

B. Emissions Unit Description

Primary use _________________________________ Temporary Source ___Yes ___No

Manufacturer ___________________________ Model No. ______________________

Serial Number __________________________ Installation Date____/____/_______

Boiler Type: ___ Industrial boiler ___ Process burner ___ Electric utility boiler

Other (describe) _____________________________________________

Boiler horsepower rating_________________ Boiler steam flow (lb/hr)_______________

Type of Fuel-Burning Equipment (coal burning only):

___ Hand fired ___Spreader stoker ___Underfeed stoker ___Overfeed stoker

___ Traveling grate ___Shaking grate ___Pulverized, wet bed ___ Pulverized, dry bed

Actual Heat Input __________MM BTU/hr Max. Design Heat Input __________MM BTU/hr

C. Fuel Data

Primary fuel type(s)____________________ Standby fuel type(s)_____________________ Describe each fuel you expected to use during the term of the permit.
Fuel Type	Max. Sulfur Content (%)	Max. Ash Content (%)	BTU Value (cf, gal., or lb.)

D. Fuel Usage Rates

Fuel Type	Annual Actual Usage	Maximum Usage
		Hourly	Annual

E. Associated Air Pollution Control Equipment

Emissions unit ID____________ Device type_______________________________________

Air pollutant(s) Controlled___________________ Manufacturer_________________________

Model No.______________________ Serial No._______________________

Installation date_____/_____/_________ Control efficiency (%) ____________

Efficiency estimation method______________________________________________

6. Ambient Impact Assessment

This information must be completed by temporary sources or when ambient impact assessment is an applicable requirement for this emissions unit (this is not common).

Stack height (ft) __________._____ Inside stack diameter (ft) _________._____

Stack temp (^oF) __________._____ Design stack flow rate (ACFM) __________.____

Actual stack flow rate (ACFM) ____________.____ Velocity (ft/sec) ____________._______

INSTRUCTIONS FOR EUD-1

EMISSIONS UNIT DESCRIPTION FOR FUEL COMBUSTION SOURCES

Use this form is to describe emissions units that combust solid or liquid fuels, such as boilers, steam generators, electric generators and the like.

Section A – The emissions unit ID should be consistent with the one used in section I of form GIS. Enter the four-digit SIC code for the unit, which may be different from that used to describe the facility as a whole. Enter the source classification code (SCC), if known or readily available (not mandatory).

Section B - There may be other information that the permitting authority will need to know that is not specifically requested on the forms and that should be included on attachments. Such information would be critical to identifying the emissions unit and its applicable requirements.

Section C - Describe the primary fuel type is that used during the majority of its operating hours. Your fuel supplier should be able to provide the information requested here. If the supplier provides a range of values, use the highest or worst-case value. Identify and describe any associated air pollution control device. If data provided by the vendor, attach documentation (if available); if other basis, indicate how determined (e.g., AP-42).

Section D - Actual fuel usage will be used to calculate actual emissions for purposes of calculating fees. Maximum usage will be used to calculate PTE. If your fuel is a combination of several fuel types, indicate the average percentage of each fuel on an hourly and yearly basis in the appropriate column or on an attachment. The basis of this fuels usage data must be explained on an attachment. For example, actual fuel consumption could be established from purchase records or records of fuel consumption over the preceding calendar year or for sources that have not yet operated for a full year, from estimations of actual usage.

Section E - Identify and describe any associated air pollution control device for the unit described above. For control efficiency, you may need to contact the vendor, if so, attach copies of correspondence from the vendor documenting these values, if available, or indicate how these values were otherwise determined.

Section F - Complete this section only if ambient impact assessment is an applicable requirement or the facility is a temporary source. This is not common.

Paperwork Reduction Act Burden Statement: This collection of information is approved by OMB under the Paperwork Reduction Act, 44 U.S.C. 3501 et seq. (OMB Control No. 2060-0036). Responses to this collection of information are mandatory (40 CFR 71). An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB control number. The public reporting and recordkeeping burden for this collection of information is estimated to 268 hours per response. Send comments on the Agency’s need for this information, the accuracy of the provided burden estimates and any suggested methods for minimizing respondent burden to the Regulatory Support Division Director, U.S. Environmental Protection Agency (2821T), 1200 Pennsylvania Ave., NW, Washington, D.C. 20460. Include the OMB control number in any correspondence. Do not send the completed form to this address

EPA Form 5900-80