NESHAP for Nine Metal Fabrication and Finishing Source Categories (40 CFR part 63, subpart XXXXXX) (Proposed Rule)

Forms and Documents

Forms and supporting documents for this ICR

Document	Type	Status	Availability
2298ss01.doc	Supporting Statement A	Uploaded 2008-03-18	Available

IC Document Collections

Information collection document groups

IC ID	Collection	Type	Status	Form
184335	NESHAP for Nine Metal Fabrication and Finishing Source Categories (40 CFR part 63, subpart XXXXXX)		New

ICR Details

OMB Control No: 2060-0613	ICR Reference No: 200804-2060-001
Status: Historical Inactive	Previous ICR Reference No:
Agency/Subagency: EPA/OAR	Agency Tracking No: 2298.01
Title: NESHAP for Nine Metal Fabrication and Finishing Source Categories (40 CFR part 63, subpart XXXXXX) (Proposed Rule)
Type of Information Collection: New collection (Request for a new OMB Control Number)	Common Form ICR:  No
Type of Review Request: Regular
OIRA Conclusion Action: Comment filed on proposed rule	Conclusion Date: 07/01/2008
	Date Received in OIRA: 04/03/2008
Terms of Clearance: This OMB action is not an approval to conduct or sponsor an information collection under the Paperwork Reduction Act of 1995. This action has no effect on any current approvals. If OMB has assigned this ICR a new OMB Control Number, the OMB Control Number will not appear in the active inventory. For future submissions of this information collection, reference the OMB Control Number provided. In accordance with 5 CFR 1320, OMB is withholding approval at this time. Prior to publication of the final rule, the agency should provide a summary of any comments related to the information collection and their response, including any changes made to the ICR as a result of comments. In addition, the agency must enter the correct burden estimates in the ROCIS system.

table that charts list comparision

	Inventory as of this Action	Requested	Previously Approved
Expiration Date		36 Months From Approved
Responses	0	0	0
Time Burden (Hours)	0	0	0
Cost Burden (Dollars)	0	0	0

---

Abstract: EPA is proposing national emission standards for hazardous air pollutants (NESHAP) for the following nine metal fabrication and finishing area source categories that were identified from the 1990 HAP inventory as contributing to urban HAP emissions of Cd, Cr, Mn. Ni, Pb: (1) Electrical and Electronic Equipment Finishing Operations, (2) Fabricated Metal Products, (3) Fabricated Plate Work (Boiler Shops), (4) Fabricated Structural Metal Manufacturing, (5)Heating Equipment, except Electric, (6) Industrial Machinery and Equipment: Finishing Operations, (7) Iron and Steel Forging, (8)Primary Metal Products Manufacturing, (9) Valves and Pipe Fittings. These nine industry sectors have five common and similar metal fabrication and finishing processes: dry abrasive blasting, dry grinding and dry polishing with machines, machining, painting, and welding. We are proposing regulations to establish generally available control technology (GACT) for these processes in the form of management practices and equipment standards. The industry is already generally well-controlled in terms of these operations.

---

Authorizing Statute(s): US Code: 42 USC 7401 Name of Law: Clean Air Act
  

Citations for New Statutory Requirements: None

---

Associated Rulemaking Information
RIN:	Stage of Rulemaking:	Federal Register Citation:	Date:
2060-AO27	Proposed rulemaking	73 FR 18333	04/03/2008

---

Federal Register Notices & Comments

Did the Agency receive public comments on this ICR? No

---

Number of Information Collection (IC) in this ICR: 1

table that charts list of burden

IC Title	Form No.	Form Name
NESHAP for Nine Metal Fabrication and Finishing Source Categories (40 CFR part 63, subpart XXXXXX)

---

Burden increases because of Program Change due to Agency Discretion: Yes

Burden Increase Due to: Changing Regulations

Burden decreases because of Program Change due to Agency Discretion: No

Burden Reduction Due to:

Short Statement: New Collection.

---

Annual Cost to Federal Government: $469,395

Does this IC contain surveys, censuses, or employ statistical methods? No

Is the Supporting Statement intended to be a Privacy Impact Assessment required by the E-Government Act of 2002? No

Is this ICR related to the Affordable Care Act [Pub. L. 111-148 & 111-152]? Uncollected

Is this ICR related to the Dodd-Frank Wall Street Reform and Consumer Protection Act, [Pub. L. 111-203]? Uncollected

Is this ICR related to the American Recovery and Reinvestment Act of 2009 (ARRA)? Uncollected

Is this ICR related to the Pandemic Response? Uncollected

---

Common Form ICR:  No

---

On behalf of this Federal agency, I certify that the collection of information encompassed by this request complies with 5 CFR 1320.9 and the related provisions of 5 CFR 1320.8(b)(3).

The following is a summary of the topics, regarding the proposed collection of information, that the certification covers:

(a) It is necessary for the proper performance of agency functions;

(b) It avoids unnecessary duplication;

(c) It reduces burden on small entities;

(d) It uses plain, coherent, and unambiguous language that is understandable to respondents;

(e) Its implementation will be consistent and compatible with current reporting and recordkeeping practices;

(f) It indicates the retention periods for recordkeeping requirements;

(g) It informs respondents of the information called for under 5 CFR 1320.8 (b)(3) about:

(i) Why the information is being collected;

(ii) Use of information;

(iii) Burden estimate;

(iv) Nature of response (voluntary, required for a benefit, or mandatory);

(v) Nature and extent of confidentiality; and

(vi) Need to display currently valid OMB control number;

(h) It was developed by an office that has planned and allocated resources for the efficient and effective management and use of the information to be collected.

(i) It uses effective and efficient statistical survey methodology (if applicable); and

(j) It makes appropriate use of information technology.

If you are unable to certify compliance with any of these provisions, identify the item by leaving the box unchecked and explain the reason in the Supporting Statement.

Certification Date: 04/03/2008

---