1064ss16

1064ss16.doc

NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM)(Renewal)

OMB: 2060-0034

Document [doc]
Download: doc | pdf

13



SUPPORTING STATEMENT

ENVIRONMENTAL PROTECTION AGENCY


NSPS for Automobile and Light Duty Truck Surface Coating Operations

(40 CFR Part 60, Subpart MM) (Renewal)


1. Identification of the Information Collection


1(a) Title of the Information Collection


NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal), EPA ICR Number 1064.16, OMB Control Number 2060-0034


1(b) Short Characterization/Abstract


The New Source Performance Standards (NSPS) for Automobile and Light Duty Truck Surface Coating Operations, published at 40 CFR part 60, subpart MM, were proposed on October 5, 1979, and promulgated on December 24, 1980 (45 FR 85415). These regulations apply to the following automobile and light duty truck assembly plant operations: each prime coat operation, guide coat operation, and top coat operation commencing construction, modification or reconstruction after October 5, 1979. This information is being collected to assure compliance with these regulations.


Approximately 52 sources are currently subject to the standard, and it is estimated that an additional two sources per year could become subject to the regulation in the next three years. This estimate is based on the previously approved Information Collection Request (ICR). The cost of this ICR will be $14,790,142 in labor costs.


The Office of Management and Budget (OMB) approved the currently active ICR without any “Terms of Clearance.”


2. Need for and Use of the Collection


2(a) Need/Authority for the Collection


The EPA is charged under Section 111 of the Clean Air Act, as amended, to establish standards of performance for new stationary sources that reflect:


. . . application of the best technological system of continuous emissions reduction which (taking into consideration the cost of achieving such emissions reduction, or any non-air quality health and environmental impact and energy requirements) the Administrator determines has been adequately demonstrated. Section 111(a)(l).


The Agency refers to this charge as selecting the best demonstrated technology (BDT). Section 111 also requires that the Administrator review and, if appropriate, revise such standards every eight years.


In addition, Section 114(a) states that the Administrator may require any owner or operator subject to any requirement of this Act to:


(A) Establish and maintain such records; (B) make such reports; (C) install, use, and maintain such monitoring equipment, and use such audit procedures, or methods; (D) sample such emissions (in accordance with such procedures or methods, at such locations, at such intervals, during such periods, and in such manner as the Administrator shall prescribe); (E) keep records on control equipment parameters, production variables or other indirect data when direct monitoring of emissions is impractical; (F) submit compliance certifications in accordance with Section 114(a)(3); and (G) provide such other information as the Administrator may reasonably require.


In the Administrator’s judgment, volatile organic compound (VOC) emissions from automobile and light duty truck coating operations cause or contribute to air pollution that may reasonably be anticipated to endanger public health or welfare. Therefore, the NSPS were promulgated for this source category at 40 CFR part 60, subpart MM.


2(b) Practical Utility/Users of the Data


The recordkeeping and reporting requirements in the standard(s) ensure compliance with the applicable regulations which where promulgated in accordance with the Clean Air Act. The collected information is also used for targeting inspections and as evidence in legal proceedings.


Performance test reports are needed as these are the Agency’s record of a source’s initial capability to comply with the emission standards, and serve as a record of the operating conditions under which compliance was achieved. When thermal or catalytic incineration is performed, the owner or operator shall keep records of each three-hour period during which the incinerator temperature averaged more than 28 degrees centigrade below the temperature of the most recent performance test, and when the average temperature difference across the catalyst bed is less than 80% of the average temperature difference recorded during the most recent performance test. The required semiannual reports are used to determine periods of excess emissions, identify problems at the facility, verify operation/maintenance procedures and for compliance determinations. The information generated by the monitoring, recordkeeping and reporting requirements described in this ICR is used by the Agency to ensure that facilities affected by the NSPS continue to operate the control equipment in compliance with the regulation. Adequate monitoring, recordkeeping, and reporting are necessary to ensure compliance with these standards, as required by the Clean Air Act. The information collected from recordkeeping and reporting requirements is also used for targeting inspections, and is of sufficient quality to be used as evidence in court.


3. Non-duplication, Consultations, and Other Collection Criteria


The requested recordkeeping and reporting are required under 40 CFR part 60, subpart MM.


3(a) Non-duplication


If the subject standards have not been delegated, the information is sent directly to the appropriate EPA regional office. Otherwise, the information is sent directly to the delegated state or local agency. If a state or local agency has adopted their own similar standards to implement the Federal standards, a copy of the report submitted to the state or local agency can be sent to the Administrator in lieu of the report required by the Federal standards; therefore, no duplication exists.


3(b) Public Notice Required Prior to ICR Submission to OMB


An announcement of a public comment period for the renewal of this ICR was published in the Federal Register (72 FR 32580) on July 8, 2009. No comments were received on the burden published in the Federal Register.


3(c) Consultations


For this information collection, the previous ICR renewal was used to obtain burden estimates since this ICR renewal was processed under the “Expedited Approach” option provided in May 1, 2008 guidance. Per this guidance, all data and assumptions from the previous ICR renewal were used as the basis for estimating the hourly and cost burdens associated with this renewal


3(d) Effects of Less Frequent Collection


Less frequent information collection would decrease the margin of assurance that facilities are continuing to meet the standards. Requirements for information gathering and recordkeeping are useful techniques to ensure that good operation and maintenance practices are applied and emission limitations are met. If the information required by these standards was collected less frequently, the proper operation and maintenance of control equipment and the possibility of detecting violations would be less likely.


3(e) General Guidelines


These reporting or recordkeeping requirements do not violate any of the regulations promulgated by OMB under 5 CFR part 1320, section 1320.5.


3(f) Confidentiality


Any information submitted to the Agency for which a claim of confidentiality is made will be safeguarded according to the Agency policies set forth in Title 40, chapter 1, part 2, subpart B - Confidentiality of Business Information (CBI) (see 40 CFR 2; 41 FR 36902, September 1, 1976; amended by 43 FR 40000, September 8, 1978; 43 FR 42251, September 20, 1978; 44 FR 17674, March 23, 1979).


3(g) Sensitive Questions


The reporting or recordkeeping requirements in the standard do not include sensitive questions.


4. The Respondents and the Information Requested


4(a) Respondents/SIC Codes


The respondents of the recordkeeping and reporting requirements are automobile and light duty truck surface coating operations for which construction or modification commenced after October 5, 1979. The SIC code for the respondents affected by the standards is SIC (U.S. Standard Industrial Classification) 3711 which corresponds to the North American Industry Classification System (NAICS) 336111, 336112, and 336211.



Standard


SIC Codes


NAICS Codes


40 CFR part 60, subpart MM


3711


336111






336112






336211

To compare the SIC and NAICS codes, see the website at http://www.census.gov/epcd/www/naics.html.


4(b) Information Requested


(i) Data Items


All data in this ICR that is recorded and/or reported is required by NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM).


A source must make the following reports:




Notifications


Construction/reconstruction


60.7(a)(1)


Actual startup


60.7(a)(3)


Initial performance test results


60.8(a)


Initial performance test


60.8(d)


Physical or operational change.


60.7(a)(4)


Startups, shutdowns, malfunctions, periods where the continuous monitoring system is inoperative.


60.7(b)


Report volume weighted average mass of VOC per volume of applied coatings solid in initial compliance report.


60.395(a)


Report the gas temperature upstream and downstream of catalyst bed, total mass of VOC per volume of applied coating solids, capture efficiency, destruction efficiency, and method used to determine VOC captured and sent to the control device in initial compliance report or subsequent performance test report.


60.395(a)


Monthly performance test.


60.393(b), 60.393(c)


Install, calibrate, maintain, and operate temperature monitoring device Quarterly reports of excess VOC emissions, semiannual reports if no exceedences.


60.395(b)


Reports of low incinerator temperature.


60.395(c)


Record the incinerator combustion temperature.


60.395(d)


Notify the Administrator 30 days in advance of any test by Reference Method 25.


60.395(d)


A source must keep the following records:



Recordkeeping


Startups, shutdowns, malfunctions, periods where the continuous monitoring system is inoperative.


60.7(b)


Records are required to be retained for two years. Records must be retained at the facility.


60.8

Electronic Reporting


Some of the respondents are using monitoring equipment that automatically records parameter data. Although personnel at the affected facility must still evaluate the data, internal automation has significantly reduced the burden associated with monitoring and recordkeeping at a plant site.


Also, regulatory agencies in cooperation with the respondents, continue to create reporting systems to transmit data electronically. However, electronic reporting systems are still not widely used. At this time, it is estimated that approximately 10 percent of the respondents use electronic reporting.


(ii) Respondent Activities



Respondent Activities


Read instructions.


Install, calibrate, maintain, and operate the compliance monitoring system (CMS) for temperature.


Perform initial performance test, Reference Method 24 or Method 25 test, and repeat performance tests if necessary.


Write the notifications and reports listed above.


Enter information required to be recorded above.


Submit the required reports developing, acquiring, installing, and utilizing technology and systems for the purpose of collecting, validating, and verifying information.


Develop, acquire, install, and utilize technology and systems for the purpose of processing and maintaining information.


Develop, acquire, install, and utilize technology and systems for the purpose of disclosing and providing information.


Adjust the existing ways to comply with any previously applicable instructions and requirements.


Train personnel to be able to respond to a collection of information.


Transmit, or otherwise disclose the information.



5. The Information Collected -- Agency Activities, Collection Methodology, and Information Management


5(a) Agency Activities


EPA conducts the following activities in connection with the acquisition, analysis, storage, and distribution of the required information.



Agency Activities


Observe initial performance tests and repeat performance tests if necessary.


Review notifications and reports, including performance test reports, and excess emissions reports, required to be submitted by industry.


Audit facility records.


Input, analyze, and maintain data in the Air Facility System (AFS).


5(b) Collection Methodology and Management


Following notification of startup, the reviewing authority might inspect the source to determine whether the pollution control devices are properly installed and operated. Performance test reports are used by the Agency to discern a source’s initial capability to comply with the emission standard, and note the operating conditions under which compliance was achieved. Data and records maintained by the respondents are tabulated and published for use in compliance and enforcement programs. The semiannual reports are used for problem identification, as a check on source operation and maintenance, and for compliance determinations.


Information contained in the reports is entered into the AFS which is operated and maintained by EPA’s Office of Compliance. AFS is EPA’s database for the collection, maintenance, and retrieval of compliance data for approximately 125,000 industrial and government-owned facilities. EPA uses the AFS for tracking air pollution compliance and enforcement by local and state regulatory agencies, EPA regional offices and EPA headquarters. EPA and its delegated Authorities can edit, store, retrieve and analyze the data.


The records required by this regulation must be retained by the owner or operator for

two years.


5(c) Small Entity Flexibility


The number of small entities potentially subject to the requirements of this ICR is estimated to be zero percent of the respondent universe. This estimate is based on the discussion at the affected small entities during the development of the rule (see BID EPA-450/3-80-003a).


5(d) Collection Schedule


The specific frequency for each information collection activity within this request is shown below in Table 1: Annual Respondent Burden and Cost - NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal).


6. Estimating the Burden and Cost of the Collection


Table 1 documents the computation of individual burdens for the recordkeeping and reporting requirements applicable to the industry for the subpart included in this ICR. The individual burdens are expressed under standardized headings believed to be consistent with the concept of burden under the Paperwork Reduction Act. Where appropriate, specific tasks and major assumptions have been identified. Responses to this information collection are mandatory.


The Agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB Control Number.


6(a) Estimating Respondent Burden


The average annual burden to industry over the next three years from these recordkeeping and reporting requirements is estimated to be 156,362 (Total Labor Hours from Table 1). The recordkeeping hours shown below in Table 1 are 151,072. The reporting requirement hours shown in Table 1 are 5,290. These hours are based on Agency studies and background documents from the development of the regulation, Agency knowledge and experience with the NSPS program, the previously approved ICR, and any comments received.


6(b) Estimating Respondent Costs


(i) Estimating Labor Costs


This ICR uses the following labor rates:


Managerial $114.49 ($54.52 + 110%)

Technical $98.20 ($46.76 + 110%)

Clerical $48.53 ($23.11 + 110%)


These rates are from the United States Department of Labor, Bureau of Labor Statistics, September 2009, “Table 2. Civilian Workers, by occupational and industry group.” The rates are from column 1, “Total compensation.” The rates have been increased by 110 percent to account for the benefit packages available to those employed by private industry.




(ii) Estimating Capital and Operations and Maintenance Costs

The type of industry costs associated with the information collection activities in the subject standard(s) are both labor costs which are addressed elsewhere in this ICR and the costs associated with continuous monitoring. The capital/startup costs are one-time costs when a facility becomes subject to the regulation. The annual operation and maintenance costs are the ongoing costs to maintain the monitor(s) and other costs such as photocopying and postage.


(iii) Capital/Startup vs. Operating and Maintenance (O&M) Costs



Capital/Startup vs. Operating and Maintenance (O&M) Costs


(A)

Continuous Monitoring Device


(B)

Capital/

Startup Cost for One Respondent


(C)

Number of New Respondents


(D)

Total Capital/

Startup Cost, (B X C)


(E)

Annual O&M Costs for One Respondent


(F)

Number of Respondents with O&M


(G)

Total O&M,

(E X F)


Temperature Monitoring Device


$850


2


$1,700


$1,750


52


$91,000

The total capital/startup costs for this ICR are $1,700. This is the total of column D in the above table.


The total operating and maintenance (O&M) costs for this ICR are $91,000. This is the total of column G.


The total respondent costs have been calculated as the addition of the capital/startup costs, and the annual operation and maintenance costs. The average annual cost for capital/startup and operation and maintenance costs to industry over the next three years of the ICR is estimated to be $92,700.


The continuous monitoring costs that are included in this section consist only of those capital/startup and O&M costs that a source incurs as a result of the standard. Some continuous monitoring costs may not be included in this section. For instance, if a particular industry typically utilizes a control device that must have a continuous monitor (e.g., temperature, pressure drop, etc.) to function properly, and the recordation of additional measurements beyond the minimum is required by the standard, then there is no capital/startup or O & M cost, but there is a labor cost to record the additional readings. Such a cost would not appear in this section, but in the industry burden Section 6(d) below.





6(c) Estimating Agency Burden and Cost


The only costs to the Agency are those costs associated with analysis of the reported information. EPA’s overall compliance and enforcement program includes activities such as the examination of records maintained by the respondents, periodic inspection of sources of emissions, and the publication and distribution of collected information.


The average annual Agency cost during the three years of the ICR is estimated to be $34,781 (rounded).


This cost is based on the average hourly labor rate as follows:


Managerial $62.27 (GS-13, Step 5, $38.92 + 60%)

Technical $46.21 (GS-12, Step 1, $28.88 + 60%)

Clerical $25.01 (GS-6, Step 3, $15.63 + 60%)



These rates are from the Office of Personnel Management (OPM), 2010 General Schedule, which excludes locality rates of pay. The rates have been increased by 60 percent to account for the benefit packages available to government employees. These rates can be obtained from the OPM web site, http//www.opm.gov/oca/payrates/index.htm. Details upon which this estimate is based appear below in Table 2: Annual Agency Burden and Cost - NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal).


6(d) Estimating the Respondent Universe and Total Burden and Costs


Approximately 52 existing sources are currently subject to the regulation, and it is estimated that an additional two sources per year could become subject to the regulation in the next three years, thus the total number of respondents, both existing and potential, is 54.


The total number of annual responses per year is calculated using the following table:



Total Annual Responses


(A)


Information Collection Activity


(B)


Number of

Respondents


(C)


Number of Responses


(D)

Number of Existing Respondents That Keep Records But Do Not Submit Reports


(E)

Total Annual Responses

E=(BxC)+D


Notification of Construction/Reconstruction


2


1


0


4


Notification of Actual Startup

2

1

0

4


Notification of Initial Performance Test

2

1

0

4


VOC Emission Reports

52

4

0

208


Temperature Reports

52

2

0

104



Total








324



The number of Total Annual Responses is 312. This is the number in column E of the Respondent Universe and Number of Responses Per Year table above.


The total annual labor costs for Respondents are $14,790,142 (rounded). Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost - NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal). Note that the total annual capital and O&M costs to the regulated entity are $92,700. These costs are detailed in Section 6(b)(iii), Capital/Startup vs. Operation and Maintenance (O&M) Costs.


6(e) Bottom Line Burden Hours Burden Hours and Cost Tables


The detailed bottom line burden hours and cost calculations for the respondents and the Agency are shown in Tables 1 and 2, respectively, and summarized below.


(i) Respondent Tally


The total annual labor hours are (number). Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost - NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal). Furthermore, the annual public reporting and recordkeeping burden for this collection of information is estimated to average 7 hours per response.


The total annual capital/startup and O&M costs to the regulated entity are $92,700. The cost calculations are detailed in Section 6(b)(iii), Capital/Startup vs. Operation and Maintenance (O&M) Costs.


(ii) The Agency Tally


The average annual Agency burden and cost over next three years is estimated to be 708 labor hours at a cost of $34,781. See below Table 2: Annual Agency Burden and Cost - NSPS for Automobile and Light Duty Truck Surface Coating Operations (40 CFR part 60, subpart MM) (Renewal).


6(f) Reasons for Change in Burden


There is a decrease in the average estimated burden as currently identified in the OMB Inventory of Approved Burdens. This decrease is not due to any program changes. The total estimated annual hour burden remained the same but the change in the average burden estimates occurred due to an incorrect calculation of the number of responses in the previous ICR. Further, the reduction in Agency burden from 760 to 708 is a result of a rounding error in the previous burden estimate.

6(g) Burden Statement


The annual public reporting and recordkeeping burden for this collection of information is estimated to average 483 (rounded) hours per response. Burden means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.


An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a valid OMB Control Number. The OMB Control Numbers for EPA’s regulations are listed at 40 CFR part 9 and 48 CFR chapter 15.


To comment on the Agency’s need for this information, the accuracy of the provided burden estimates, and any suggested methods for minimizing respondent burden, including the use of automated collection techniques, EPA has established a public docket for this ICR under Docket ID Number EPA-HQ-OECA-2009-0414. An electronic version of the public docket is available at http://www.regulations.gov/ which may be used to obtain a copy of the draft collection of information, submit or view public comments, access the index listing of the contents of the docket, and to access those documents in the public docket that are available electronically. When in the system, select “search,” then key in the docket ID number identified in this document. The documents are also available for public viewing at the Enforcement and Compliance Docket and Information Center in the EPA Docket Center (EPA/DC), EPA West, Room 3334, 1301 Constitution Ave., NW, Washington, DC. The EPA Docket Center Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number for the Reading Room is (202) 566-1744, and the telephone number for the Enforcement and Compliance Docket and Information Center Docket is (202) 566-1752. Also, you can send comments to the Office of Information and Regulatory Affairs, Office of Management and Budget, 725 17th Street, NW, Washington, DC 20503, Attention: Desk Office for EPA. Please include the EPA Docket ID Number EPA-HQ-OECA-2009-0414 and OMB Control Number 2060-0034 in any correspondence.


Part B of the Supporting Statement

This part is not applicable because no statistical methods were used in collecting this information.


File Typeapplication/msword
Last Modified Byctsuser
File Modified2010-04-22
File Created2010-04-22

© 2024 OMB.report | Privacy Policy