29 Cfr 1910.217

Electronic Code of Federal Regulations
e-CFR data is current as of October 1, 2018
Title 29 → Subtitle B → Chapter XVII → Part 1910 → Subpart O → §1910.217

Browse Previous | Browse Next

Title 29: Labor
PART 1910—OCCUPATIONAL SAFETY AND HEALTH STANDARDS
Subpart O—Machinery and Machine Guarding

§1910.217 Mechanical power presses.
(a) General requirements. (1)-(3) [Reserved]
(4) Reconstruction and modification. It shall be the responsibility of any person reconstructing, or
modifying a mechanical power press to do so in accordance with paragraph (b) of this section.
(5) Excluded machines. Press brakes, hydraulic and pneumatic power presses, bulldozers, hot bending
and hot metal presses, forging presses and hammers, riveting machines and similar types of fastener
applicators are excluded from the requirements of this section.
(b) Mechanical power press guarding and construction, general—(1) Hazards to personnel associated
with broken or falling machine components. Machine components shall be designed, secured, or covered to
minimize hazards caused by breakage, or loosening and falling or release of mechanical energy (i.e. broken
springs).
(2) Brakes. Friction brakes provided for stopping or holding a slide movement shall be inherently selfengaging by requiring power or force from an external source to cause disengagement. Brake capacity shall be
sufficient to stop the motion of the slide quickly and capable of holding the slide and its attachments at any
point in its travel.
(3) Machines using full revolution positive clutches. (i) Machines using full revolution clutches shall
incorporate a single-stroke mechanism.
(ii) If the single-stroke mechanism is dependent upon spring action, the spring(s) shall be of the
compression type, operating on a rod or guided within a hole or tube, and designed to prevent interleaving of
the spring coils in event of breakage.
(4) Foot pedals (treadle). (i) The pedal mechanism shall be protected to prevent unintended operation
from falling or moving objects or by accidental stepping onto the pedal.
(ii) A pad with a nonslip contact area shall be firmly attached to the pedal.
(iii) The pedal return spring(s) shall be of the compression type, operating on a rod or guided within a
hole or tube, or designed to prevent interleaving of spring coils in event of breakage.

(iv) If pedal counterweights are provided, the path of the travel of the weight shall be enclosed.
(5) Hand operated levers. (i) Hand-lever-operated power presses shall be equipped with a spring latch on
the operating lever to prevent premature or accidental tripping.
(ii) The operating levers on hand-tripped presses having more than one operating station shall be
interlocked to prevent the tripping of the press except by the “concurrent” use of all levers.
(6) Two-hand trip. (i) A two-hand trip shall have the individual operator's hand controls protected against
unintentional operation and have the individual operator's hand controls arranged by design and construction
and/or separation to require the use of both hands to trip the press and use a control arrangement requiring
concurrent operation of the individual operator's hand controls.
(ii) Two-hand trip systems on full revolution clutch machines shall incorporate an antirepeat feature.
(iii) If two-hand trip systems are used on multiple operator presses, each operator shall have a separate
set of controls.
(7) Machines using part revolution clutches. (i) The clutch shall release and the brake shall be applied
when the external clutch engaging means is removed, deactivated, or deenergized.
(ii) A red color stop control shall be provided with the clutch/brake control system. Momentary operation
of the stop control shall immediately deactivate the clutch and apply the brake. The stop control shall override
any other control, and reactuation of the clutch shall require use of the operating (tripping) means which has
been selected.
(iii) A means of selecting Off, “Inch,” Single Stroke, and Continuous (when the continuous function is
furnished) shall be supplied with the clutch/brake control to select type of operation of the press. Fixing of
selection shall be by means capable of supervision by the employer.
(iv) The “Inch” operating means shall be designed to prevent exposure of the workers hands within the
point of operation by:
(a) Requiring the concurrent use of both hands to actuate the clutch, or
(b) Being a single control protected against accidental actuation and so located that the worker cannot
reach into the point of operation while operating the single control.
(v) Two-hand controls for single stroke shall conform to the following requirements:
(a) Each hand control shall be protected against unintended operation and arranged by design,
construction, and/or separation so that the concurrent use of both hands is required to trip the press.
(b) The control system shall be designed to permit an adjustment which will require concurrent pressure
from both hands during the die closing portion of the stroke.
(c) The control system shall incorporate an antirepeat feature.
(d) The control systems shall be designed to require release of all operators' hand controls before an
interrupted stroke can be resumed. This requirement pertains only to those single-stroke, two-hand controls
manufactured and installed on or after August 31, 1971.

(vi) [Reserved]
(vii) Controls for more than one operating station shall be designed to be activated and deactivated in
complete sets of two operator's hand controls per operating station by means capable of being supervised by
the employer. The clutch/brake control system shall be designed and constructed to prevent actuation of the
clutch if all operating stations are bypassed.
(viii) Those clutch/brake control systems which contain both single and continuous functions shall be
designed so that completion of continuous circuits may be supervised by the employer. The initiation of
continuous run shall require a prior action or decision by the operator in addition to the selection of Continuous
on the stroking selector, before actuation of the operating means will result in continuous stroking.
(ix) If foot control is provided, the selection method between hand and foot control shall be separate from
the stroking selector and shall be designed so that the selection may be supervised by the employer.
(x) Foot operated tripping controls, if used, shall be protected so as to prevent operation from falling or
moving objects, or from unintended operation by accidental stepping onto the foot control.
(xi) The control of air-clutch machines shall be designed to prevent a significant increase in the normal
stopping time due to a failure within the operating value mechanism, and to inhibit further operation if such
failure does occur. This requirement shall apply only to those clutch/brake air-valve controls manufactured and
installed on or after August 31, 1971, but shall not apply to machines intended only for continuous, automatic
feeding applications.
(xii) The clutch/brake control shall incorporate an automatic means to prevent initiation or continued
activation of the Single Stroke or Continuous functions unless the press drive motor is energized and in the
forward direction.
(xiii) The clutch/brake control shall automatically deactivate in event of failure of the power or pressure
supply for the clutch engaging means. Reactivation of the clutch shall require restoration of normal supply and
the use of the tripping mechanism(s).
(xiv) The clutch/brake control shall automatically deactivate in event of failure of the counterbalance(s)
air supply. Reactivation of the clutch shall require restoration of normal air supply and use of the tripping
mechanism(s).
(xv) Selection of bar operation shall be by means capable of being supervised by the employer. A
separate pushbutton shall be employed to activate the clutch, and the clutch shall be activated only if the driver
motor is deenergized.
(8) Electrical. (i) A main power disconnect switch capable of being locked only in the Off position shall
be provided with every power press control system.
(ii) The motor start button shall be protected against accidental operation.
(iii) All mechanical power press controls shall incorporate a type of drive motor starter that will
disconnect the drive motor from the power source in event of control voltage or power source failure, and
require operation of the motor start button to restart the motor when voltage conditions are restored to normal.
(iv) All a.c. control circuits and solenoid value coils shall be powered by not more than a nominal 120volt a.c. supply obtained from a transformer with an isolated secondary. Higher voltages that may be necessary

for operation of machine or control mechanisms shall be isolated from any control mechanism handled by the
operator, but motor starters with integral Start-Stop buttons may utilize line voltage control. All d.c. control
circuits shall be powered by not more than a nominal 240-volt d.c. supply isolated from any higher voltages.
(v) All clutch/brake control electrical circuits shall be protected against the possibility of an accidental
ground in the control circuit causing false operation of the press.
(vi) Electrical clutch/brake control circuits shall incorporate features to minimize the possibility of an
unintended stroke in the event of the failure of a control component to function properly, including relays, limit
switches, and static output circuits.
(9) Slide counterbalance systems. (i) Spring counterbalance systems when used shall incorporate means
to retain system parts in event of breakage.
(ii) Spring counterbalances when used shall have the capability to hold the slide and its attachments at
midstroke, without brake applied.
(iii) Air counterbalance cylinders shall incorporate means to retain the piston and rod in case of breakage
or loosening.
(iv) Air counterbalance cylinders shall have adequate capability to hold the slide and its attachments at
any point in stroke, without brake applied.
(v) Air counterbalance cylinders shall incorporate means to prevent failure of capability (sudden loss of
pressure) in event of air supply failure.
(10) Air controlling equipment. Air controlling equipment shall be protected against foreign material and
water entering the pneumatic system of the press. A means of air lubrication shall be provided when needed.
(11) Hydraulic equipment. The maximum anticipated working pressures in any hydraulic system on a
mechanical power press shall not exceed the safe working pressure rating of any component used in that
system.
(12) Pressure vessels. All pressure vessels used in conjunction with power presses shall conform to the
American Society of Mechanical Engineers Code for Pressure Vessels, 1968 Edition, which is incorporated by
reference as specified in §1910.6.
(13) Control reliability. When required by paragraph (c)(5) of this section, the control system shall be
constructed so that a failure within the system does not prevent the normal stopping action from being applied
to the press when required, but does prevent initiation of a successive stroke until the failure is corrected. The
failure shall be detectable by a simple test, or indicated by the control system. This requirement does not apply
to those elements of the control system which have no effect on the protection against point of operation
injuries.
(14) Brake system monitoring. When required by paragraph (c)(5) of this section, the brake monitor shall
meet the following requirements:
(i) Be so constructed as to automatically prevent the activation of a successive stroke if the stopping time
or braking distance deteriorates to a point where the safety distance being utilized does not meet the
requirements set forth in paragraph (c)(3)(iii)(e) or (c)(3)(vii)(c) of this section. The brake monitor used with

the Type B gate or movable barrier device shall be installed in a manner to detect slide top-stop overrun
beyond the normal limit reasonably established by the employer.
(ii) Be installed on a press such that it indicates when the performance of the braking system has
deteriorated to the extent described in paragraph (b)(14)(i) of this section; and
(iii) Be constructed and installed in a manner to monitor brake system performance on each stroke.
(c) Safeguarding the point of operation—(1) General requirements. (i) It shall be the responsibility of the
employer to provide and insure the usage of “point of operation guards” or properly applied and adjusted point
of operation devices on every operation performed on a mechanical power press. See Table O-10.
(ii) The requirement of paragraph (c)(1)(i) of this section shall not apply when the point of operation
opening is one-fourth inch or less. See Table O-10.
(2) Point of operation guards. (i) Every point of operation guard shall meet the following design,
construction, application, and adjustment requirements:
(a) It shall prevent entry of hands or fingers into the point of operation by reaching through, over, under
or around the guard;
(b) It shall conform to the maximum permissible openings of Table O-10;
(c) It shall, in itself, create no pinch point between the guard and moving machine parts;
(d) It shall utilize fasteners not readily removable by operator, so as to minimize the possibility of misuse
or removal of essential parts;
(e) It shall facilitate its inspection, and
(f) It shall offer maximum visibility of the point of operation consistent with the other requirements.
(ii) A die enclosure guard shall be attached to the die shoe or stripper in a fixed position.
(iii) A fixed barrier guard shall be attached securely to the frame of the press or to the bolster plate.
(iv) An interlocked press barrier guard shall be attached to the press frame or bolster and shall be
interlocked with the press clutch control so that the clutch cannot be activated unless the guard itself, or the
hinged or movable sections of the guard are in position to conform to the requirements of Table O-10.
(v) The hinged or movable sections of an interlocked press barrier guard shall not be used for manual
feeding. The guard shall prevent opening of the interlocked section and reaching into the point of operation
prior to die closure or prior to the cessation of slide motion. See paragraph (c)(3)(ii) of this section regarding
manual feeding through interlocked press barrier devices.
(vi) The adjustable barrier guard shall be securely attached to the press bed, bolster plate, or die shoe, and
shall be adjusted and operated in conformity with Table O-10 and the requirements of this subparagraph.
Adjustments shall be made only by authorized personnel whose qualifications include a knowledge of the
provisions of Table O-10 and this subparagraph.

(vii) A point of operation enclosure which does not meet the requirements of this subparagraph and Table
O-10 shall be used only in conjunction with point of operation devices.
(3) Point of operation devices. (i) Point of operation devices shall protect the operator by:
(a) Preventing and/or stopping normal stroking of the press if the operator's hands are inadvertently
placed in the point of operation; or
(b) Preventing the operator from inadvertently reaching into the point of operation, or withdrawing his
hands if they are inadvertently located in the point of operation, as the dies close; or
(c) Preventing the operator from inadvertently reaching into the point of operation at all times; or
(d) [Reserved]
(e) Requiring application of both of the operator's hands to machine operating controls and locating such
controls at such a safety distance from the point of operation that the slide completes the downward travel or
stops before the operator can reach into the point of operation with his hands; or
(f) Enclosing the point of operation before a press stroke can be initiated, and maintaining this closed
condition until the motion of the slide had ceased; or
(g) Enclosing the point of operation before a press stroke can be initiated, so as to prevent an operator
from reaching into the point of operation prior to die closure or prior to cessation of slide motion during the
downward stroke.
(ii) A gate or movable barrier device shall protect the operator as follows:
(a) A Type A gate or movable barrier device shall protect the operator in the manner specified in
paragraph (c)(3)(i)(f) of this section, and
(b) A Type B gate or movable barrier device shall protect the operator in the manner specified in
paragraph (c)(3)(i)(g) of this section.
(iii) A presence sensing point of operation device shall protect the operator as provided in paragraph
(c)(3)(i)(a) of this section, and shall be interlocked into the control circuit to prevent or stop slide motion if the
operator's hand or other part of his body is within the sensing field of the device during the downstroke of the
press slide.
(a) The device may not be used on machines using full revolution clutches.
(b) The device may not be used as a tripping means to initiate slide motion, except when used in total
conformance with paragraph (h) of this section.
(c) The device shall be constructed so that a failure within the system does not prevent the normal
stopping action from being applied to the press when required, but does prevent the initiation of a successive
stroke until the failure is corrected. The failure shall be indicated by the system.
(d) Muting (bypassing of the protective function) of such device, during the upstroke of the press slide, is
permitted for the purpose of parts ejection, circuit checking, and feeding.

(e) The safety distance (Ds) from the sensing field to the point of operation shall be greater than the
distance determined by the following formula:
Ds = 63 inches/second × Ts
where:
Ds = minimum safety distance (inches); 63 inches/second = hand speed constant;
and
Ts = stopping time of the press measured at approximately 90° position of crankshaft rotation (seconds).

(f) Guards shall be used to protect all areas of entry to the point of operation not protected by the
presence sensing device.
(iv) The pull-out device shall protect the operator as specified in paragraph (c)(3)(i)(b) of this section,
and shall include attachments for each of the operator's hands.
(a) Attachments shall be connected to and operated only by the press slide or upper die.
(b) Attachments shall be adjusted to prevent the operator from reaching into the point of operation or to
withdraw the operator's hands from the point of operation before the dies close.
(c) A separate pull-out device shall be provided for each operator if more than one operator is used on a
press.
(d) Each pull-out device in use shall be visually inspected and checked for proper adjustment at the start
of each operator shift, following a new die set-up, and when operators are changed. Necessary maintenance or
repair or both shall be performed and completed before the press is operated. Records of inspections and
maintenance shall be kept in accordance with paragraph (e) of this section.
(v) The sweep device may not be used for point of operation safeguarding.
(vi) A holdout or a restraint device shall protect the operator as specified in paragraph (c)(3)(i)(c) of this
section and shall include attachments for each of the operator's hands. Such attachments shall be securely
anchored and adjusted in such a way that the operator is restrained from reaching into the point of operation. A
separate set of restraints shall be provided for each operator if more than one operator is required on a press.
(vii) The two hand control device shall protect the operator as specified in paragraph (c)(3)(i)(e) of this
section.
(a) When used in press operations requiring more than one operator, separate two hand controls shall be
provided for each operator, and shall be designed to require concurrent application of all operators' controls to
activate the slide. The removal of a hand from any control button shall cause the slide to stop.
(b) Each two hand control shall meet the construction requirements of paragraph (b)(7)(v) of this section.
(c) The safety distance (Ds) between each two hand control device and the point of operation shall be
greater than the distance determined by the following formula:
Ds = 63 inches/second × Ts;

where:
Ds = minimum safety distance (inches); 63 inches/second = hand speed constant;
and
Ts = stopping time of the press measured at approximately 90° position of crankshaft rotation (seconds).

(d) Two hand controls shall be fixed in position so that only a supervisor or safety engineer is capable of
relocating the controls.
(viii) The two hand trip device shall protect the operator as specified in paragraph (c)(3)(i)(e) of this
section.
(a) When used in press operations requiring more than one operator, separate two hand trips shall be
provided for each operator, and shall be designed to require concurrent application of all operators' to activate
the slide.
(b) Each two hand trip shall meet the construction requirements of paragraph (b)(6) of this section.
(c) The safety distance (Dm) between the two hand trip and the point of operation shall be greater than the
distance determined by the following formula:
Dm = 63 inches/second × Tm;
where:
Dm = minimum safety distance (inches); 63 inches/second = hand speed constant;
and
Tm = the maximum time the press takes for the die closure after it has been tripped (seconds). For full revolution clutch presses
with only one engaging point Tm is equal to the time necessary for one and one-half revolutions of the crankshaft.
For full revolution clutch presses with more than one engaging point, Tm shall be calculated as follows:
Tm = [ 1⁄2 + (1 ÷ Number of engaging points per revolution)] × time necessary to complete one revolution of the crankshaft
(seconds).

(d) Two hand trips shall be fixed in position so that only a supervisor or safety engineer is capable of
relocating the controls.
(4) Hand feeding tools. Hand feeding tools are intended for placing and removing materials in and from
the press. Hand feeding tools are not a point of operation guard or protection device and shall not be used in
lieu of the “guards” or devices required in this section.
(5) Additional requirements for safe-guarding. Where the operator feeds or removes parts by placing one
or both hands in the point of operation, and a two hand control, presence sensing device, Type B gate or
movable barrier (on a part revolution clutch) is used for safeguarding:
(i) The employer shall use a control system and a brake monitor which comply with paragraphs (b) (13)
and (14) of this section;

(ii) The exception in paragraph (b)(7)(v)(d) of this section for two hand controls manufactured and
installed before August 31, 1971 is not applicable under this paragraph (c)(5);
(iii) The control of air clutch machines shall be designed to prevent a significant increase in the normal
stopping time due to a failure within the operating valve mechanism, and to inhibit further operation if such
failure does occur, where a part revolution clutch is employed. The exception in paragraph (b)(7)(xi) of this
section for controls manufactured and installed before August 31, 1971, is not applicable under this paragraph
(c)(5).
(d) Design, construction, setting and feeding of dies—(1) General requirements. The employer shall: (i)
Use dies and operating methods designed to control or eliminate hazards to operating personnel, and (ii)
furnish and enforce the use of hand tools for freeing and removing stuck work or scrap pieces from the die, so
that no employee need reach into the point of operation for such purposes.
(2) [Reserved]
(3) Scrap handling. The employer shall provide means for handling scrap from roll feed or random
length stock operations. Scrap cutters used in conjunction with scrap handling systems shall be safeguarded in
accordance with paragraph (c) of this section and with §1910.219.
(4) Guide post hazard. The hazard created by a guide post (when it is located in the immediate vicinity of
the operator) when separated from its bushing by more than one-fourth inch shall be considered as a point of
operation hazard and be protected in accordance with paragraph (c) of this section.
(5) Unitized tooling. If unitized tooling is used, the opening between the top of the punch holder and the
face of the slide, or striking pad, shall be safeguarded in accordance with the requirements of paragraph (c) of
this section.
(6) Tonnage, stroke, and weight designation. All dies shall be:
(i) Stamped with the tonnage and stroke requirements, or have these characteristics recorded if these
records are readily available to the die setter;
(ii) Stamped to indicate upper die weight when necessary for air counterbalance pressure adjustment; and
(iii) Stamped to indicate complete die weight when handling equipment may become overloaded.
(7) Die fastening. Provision shall be made in both the upper and lower shoes for securely mounting the
die to the bolster and slide. Where clamp caps or setscrews are used in conjunction with punch stems,
additional means of securing the upper shoe to the slide shall be used.
(8) Die handling. Handling equipment attach points shall be provided on all dies requiring mechanical
handling.
(9) Diesetting. (i) The employer shall establish a diesetting procedure that will insure compliance with
paragraph (c) of this section.
(ii) The employer shall provide spring loaded turnover bars, for presses designed to accept such turnover
bars.

(iii) The employer shall provide die stops or other means to prevent losing control of the die while setting
or removing dies in presses which are inclined.
(iv) The employer shall provide and enforce the use of safety blocks for use whenever dies are being
adjusted or repaired in the press.
(v) The employer shall provide brushes, swabs, lubricating rolls, and automatic or manual pressure guns
so that operators and diesetters shall not be required to reach into the point of operation or other hazard areas to
lubricate material, punches or dies.
(e) Inspection, maintenance, and modification of presses—(1) Inspection and maintenance records. The
employer shall establish and follow an inspection program having a general component and a directed
component.
(i) Under the general component of the inspection program, the employer shall:
(A) Conduct periodic and regular inspections of each power press to ensure that all of its parts, auxiliary
equipment, and safeguards, including the clutch/brake mechanism, antirepeat feature, and single-stroke
mechanism, are in a safe operating condition and adjustment;
(B) Perform and complete necessary maintenance or repair, or both, before operating the press; and
(C) Maintain a certification record of each inspection, and each maintenance and repair task performed,
under the general component of the inspection program that includes the date of the inspection, maintenance,
or repair work, the signature of the person who performed the inspection, maintenance, or repair work, and the
serial number, or other identifier, of the power press inspected, maintained, and repaired.
(ii) Under the directed component of the inspection program, the employer shall:
(A) Inspect and test each press on a regular basis at least once a week to determine the condition of the
clutch/brake mechanism, antirepeat feature, and single-stroke mechanism;
(B) Perform and complete necessary maintenance or repair, or both, on the clutch/brake mechanism,
antirepeat feature, and single-stroke mechanism before operating the press; and
(C) Maintain a certification record of each maintenance task performed under the directed component of
the inspection program that includes the date of the maintenance task, the signature of the person who
performed the maintenance task, and the serial number, or other identifier, of the power press maintained.
NOTE TO PARAGRAPH (e)(1)(ii): Inspections of the clutch/brake mechanism, antirepeat feature, and single-stroke mechanism
conducted under the directed component of the inspection program are exempt from the requirement to maintain certification
records specified by paragraph (e)(1)(i)(C) of this section, but inspections of the clutch/brake mechanism, antirepeat feature, and
single-stroke mechanism conducted under the general component of the inspection program are not exempt from this
requirement.

(iii) Paragraph (e)(1)(ii) of this section does not apply to presses that comply with paragraphs (b)(13) and
(14) of this section.
(2) Modification. It shall be the responsibility of any person modifying a power press to furnish
instructions with the modification to establish new or changed guidelines for use and care of the power press
so modified.

(3) Training of maintenance personnel. It shall be the responsibility of the employer to insure the original
and continuing competence of personnel caring for, inspecting, and maintaining power presses.
(f) Operation of power presses—(1) [Reserved]
(2) Instruction to operators. The employer shall train and instruct the operator in the safe method of work
before starting work on any operation covered by this section. The employer shall insure by adequate
supervision that correct operating procedures are being followed.
(3) Work area. The employer shall provide clearance between machines so that movement of one
operator will not interfere with the work of another. Ample room for cleaning machines, handling material,
work pieces, and scrap shall also be provided. All surrounding floors shall be kept in good condition and free
from obstructions, grease, oil, and water.
(4) Overloading. The employer shall operate his presses within the tonnage and attachment weight
ratings specified by the manufacturer.

View or download PDF

Explanation of above diagram:
This diagram shows the accepted safe openings between the bottom edge of a guard and feed table at various distances
from the danger line (point of operation).
The clearance line marks the distance required to prevent contact between guard and moving parts.
The minimum guarding line is the distance between the infeed side of the guard and the danger line which is one-half inch
from the danger line.
The various openings are such that for average size hands an operator's fingers won't reach the point of operation.
After installation of point of operation guards and before a job is released for operation a check should be made to verify
that the guard will prevent the operator's hands from reaching the point of operation.
TABLE O-10
[In inches]

Distance of opening from point of operation hazard
⁄2 to 11⁄2

1

Maximum width of opening
⁄4

1

11⁄2 to 21⁄2

3

⁄8

21⁄2 to 31⁄2

1

31⁄2 to 51⁄2

5

51⁄2 to 61⁄2

3

61⁄2 to 71⁄2

7

⁄2
⁄8
⁄4
⁄8

71⁄2 to 121⁄2

11⁄4

121⁄2 to 151⁄2

11⁄2

151⁄2 to 171⁄2

17⁄8

171⁄2 to 311⁄2

21⁄8

This table shows the distances that guards shall be positioned from the danger line in accordance with the required
openings.

(g) Reports of injuries to employees operating mechanical power presses. (1) The employer shall report,
within 30 days of the occurrence, all point-of-operation injuries to operators or other employees to either the
Director of the Directorate of Standards and Guidance at OSHA, U.S. Department of Labor, Washington, DC
20210 or electronically at http://www.osha.gov/pls/oshaweb/mechanical.html; or to the State Agency
administering a plan approved by the Assistant Secretary of Labor for Occupational Safety and Health.
(2) The report shall include the following information:
(i) Employer's name, address and location of the workplace (establishment).
(ii) Employee's name, injury sustained, and the task being performed (operation, set-up, maintenance, or
other).
(iii) Type of clutch used on the press (full revolution, part revolution, or direct drive).
(iv) Type of safeguard(s) being used (two hand control, two hand trip, pullouts, sweeps, or other). If the
safeguard is not described in this section, give a complete description.
(v) Cause of the accident (repeat of press, safeguard failure, removing stuck part or scrap, no safeguard
provided, no safeguard in use, or other).
(vi) Type of feeding (manual with hands in dies or with hands out of dies, semiautomatic, automatic, or
other).
(vii) Means used to actuate press stroke (foot trip, foot control, hand trip, hand control, or other).
(viii) Number of operators required for the operation and the number of operators provided with controls
and safeguards.
(h) Presence sensing device initiation (PSDI)—(1) General. (i) The requirements of paragraph (h) shall
apply to all part revolution mechanical power presses used in the PSDI mode of operation.

(ii) The relevant requirements of paragraphs (a) through (g) of this section also shall apply to all presses
used in the PSDI mode of operation, whether or not cross referenced in this paragraph (h). Such crossreferencing of specific requirements from paragraphs (a) through (g) of this section is intended only to enhance
convenience and understanding in relating to the new provisions to the existing standard, and is not to be
construed as limiting the applicability of other provisions in paragraphs (a) through (g) of this section.
(iii) Full revolution mechanical power presses shall not be used in the PSDI mode of operation.
(iv) Mechanical power presses with a configuration which would allow a person to enter, pass through,
and become clear of the sensing field into the hazardous portion of the press shall not be used in the PSDI
mode of operation.
(v) The PSDI mode of operation shall be used only for normal production operations. Die-setting and
maintenance procedures shall comply with paragraphs (a) through (g) of this section, and shall not be done in
the PSDI mode.
(2) Brake and clutch requirements. (i) Presses with flexible steel band brakes or with mechanical linkage
actuated brakes or clutches shall not be used in the PSDI mode.
(ii) Brake systems on presses used in the PSDI mode shall have sufficient torque so that each average
value of stopping times (Ts) for stops initiated at approximately 45 degrees, 60 degrees, and 90 degrees,
respectively, of crankshaft angular position, shall not be more than 125 percent of the average value of the
stopping time at the top crankshaft position. Compliance with this requirement shall be determined by using
the heaviest upper die to be used on the press, and operating at the fastest press speed if there is speed
selection.
(iii) Where brake engagement and clutch release is effected by spring action, such spring(s) shall operate
in compression on a rod or within a hole or tube, and shall be of non-interleaving design.
(3) Pneumatic systems. (i) Air valve and air pressure supply/control.
(A) The requirements of paragraphs (b)(7)(xiii), (b)(7)(xiv), (b)(10), (b)(12) and (c)(5)(iii) of this section
apply to the pneumatic systems of machines used in the PSDI mode.
(B) The air supply for pneumatic clutch/brake control valves shall incorporate a filter, an air regulator,
and, when necessary for proper operation, a lubricator.
(C) The air pressure supply for clutch/brake valves on machines used in the PSDI mode shall be
regulated to pressures less than or equal to the air pressure used when making the stop time measurements
required by paragraph (h)(2)(ii) of this section.
(ii) Air counterbalance systems.
(A) Where presses that have slide counterbalance systems are used in the PSDI mode, the counterbalance
system shall also meet the requirements of paragraph (b)(9) of this section.
(B) Counterbalances shall be adjusted in accordance with the press manufacturer's recommendations to
assure correct counterbalancing of the slide attachment (upper die) weight for all operations performed on
presses used in the PSDI mode. The adjustments shall be made before performing the stopping time
measurements required by paragraphs (h)(2)(ii), (h)(5)(iii), and (h)(9)(v) of this section.

(4) Flywheels and bearings. Presses whose designs incorporate flywheels running on journals on the
crankshaft or back shaft, or bull gears running on journals mounted on the crankshaft, shall be inspected,
lubricated, and maintained as provided in paragraph (h)(10) of this section to reduce the possibility of
unintended and uncontrolled press strokes caused by bearing seizure.
(5) Brake monitoring. (i) Presses operated in the PSDI mode shall be equipped with a brake monitor that
meets the requirements of paragraphs (b)(13) and (b)(14) of this section. In addition, the brake monitor shall be
adjusted during installation certification to prevent successive stroking of the press if increases in stopping
time cause an increase in the safety distance above that required by paragraph (h)(9)(v) of this section.
(ii) Once the PSDI safety system has been certified/validated, adjustment of the brake monitor shall not
be done without prior approval of the validation organization for both the brake monitor adjustment and the
corresponding adjustment of the safety distance. The validation organization shall in its installation validation,
state that in what circumstances, if any, the employer has advance approval for adjustment, when prior oral
approval is appropriate and when prior approval must be in writing. The adjustment shall be done under the
supervision of an authorized person whose qualifications include knowledge of safety distance requirements
and experience with the brake system and its adjustment. When brake wear or other factors extend press
stopping time beyond the limit permitted by the brake monitor, adjustment, repair, or maintenance shall be
performed on the brake or other press system element that extends the stopping time.
(iii) The brake monitor setting shall allow an increase of no more than 10 percent of the longest stopping
time for the press, or 10 milliseconds, whichever is longer, measured at the top of the stroke.
(6) Cycle control and control systems. (i) The control system on presses used in the PSDI mode shall
meet the applicable requirements of paragraphs (b)(7), (b)(8), (b)(13), and (c)(5) of this section.
(ii) The control system shall incorporate a means of dynamically monitoring for decoupling of the rotary
position indicating mechanism drive from the crankshaft. This monitor shall stop slide motion and prevent
successive press strokes if decoupling occurs, or if the monitor itself fails.
(iii) The mode selection means of paragraph (b)(7)(iii) of this section shall have at least one position for
selection of the PSDI mode. Where more than one interruption of the light sensing field is used in the initiation
of a stroke, either the mode selection means must have one position for each function, or a separate selection
means shall be provided which becomes operable when the PSDI mode is selected. Selection of PSDI mode
and the number of interruptions/withdrawals of the light sensing field required to initiate a press cycle shall be
by means capable of supervision by the employer.
(iv) A PSDI set-up/reset means shall be provided which requires an overt action by the operator, in
addition to PSDI mode selection, before operation of the press by means of PSDI can be started.
(v) An indicator visible to the operator and readily seen by the employer shall be provided which shall
clearly indicate that the system is set-up for cycling in the PSDI mode.
(vi) The control system shall incorporate a timer to deactivate PSDI when the press does not stroke
within the period of time set by the timer. The timer shall be manually adjustable, to a maximum time of 30
seconds. For any timer setting greater than 15 seconds, the adjustment shall be made by the use of a special
tool available only to authorized persons. Following a deactivation of PSDI by the timer, the system shall
make it necessary to reset the set-up/reset means in order to reactivate the PSDI mode.
(vii) Reactivation of PSDI operation following deactivation of the PSDI mode from any other cause, such
as activation of the red color stop control required by paragraph (b)(7)(ii) of this section, interruption of the

presence sensing field, opening of an interlock, or reselection of the number of sensing field
interruptions/withdrawals required to cycle the press, shall require resetting of the set-up/reset means.
(viii) The control system shall incorporate an automatic means to prevent initiation or continued
operation in the PSDI mode unless the press drive motor is energized in the forward direction of crankshaft
rotation.
(ix) The control design shall preclude any movement of the slide caused by operation of power on, power
off, or selector switches, or from checks for proper operations as required by paragraph (h)(6)(xiv) of this
section.
(x) All components and subsystems of the control system shall be designed to operate together to provide
total control system compliance with the requirements of this section.
(xi) Where there is more than one operator of a press used for PSDI, each operator shall be protected by a
separate, independently functioning, presence sensing device. The control system shall require that each
sensing field be interrupted the selected number of times prior to initiating a stroke. Further, each operator
shall be provided with a set-up/reset means that meets the requirements of paragraph (h)(6) of this section, and
which must be actuated to initiate operation of the press in the PSDI mode.
(xii) [Reserved]
(xiii) The Control system shall incorporate interlocks for supplemental guards, if used, which will
prevent stroke initiation or will stop a stroke in progress if any supplemental guard fails or is deactivated.
(xiv) The control system shall perform checks for proper operation of all cycle control logic element
switches and contacts at least once each cycle. Control elements shall be checked for correct status after power
“on” and before the initial PSDI stroke.
(xv) The control system shall have provisions for an “inch” operating means meeting the requirements of
paragraph (b)(7)(iv) of this section. Die-setting shall not be done in the PSDI mode. Production shall not be
done in the “inch” mode.
(xvi) The control system shall permit only a single stroke per initiation command.
(xvii) Controls with internally stored programs (e.g., mechanical, electro-mechanical, or electronic) shall
meet the requirements of paragraph (b)(13) of this section, and shall default to a predetermined safe condition
in the event of any single failure within the system. Programmable controllers which meet the requirements for
controls with internally stored programs stated above shall be permitted only if all logic elements affecting the
safety system and point of operation safety are internally stored and protected in such a manner that they
cannot be altered or manipulated by the user to an unsafe condition.
(7) Environmental requirements. Control components shall be selected, constructed, and connected
together in such a way as to withstand expected operational and environmental stresses, at least including those
outlined in appendix A. Such stresses shall not so affect the control system as to cause unsafe operation.
(8) Safety system. (i) Mechanical power presses used in the PSDI mode shall be operated under the
control of a safety system which, in addition to meeting the applicable requirements of paragraphs (b)(13) and
(c)(5) and other applicable provisions of this section, shall function such that a single failure or single
operating error shall not cause injury to personnel from point of operation hazards.

(ii) The safety system shall be designed, constructed, and arranged as an integral total system, including
all elements of the press, the controls, the safeguarding and any required supplemental safeguarding, and their
interfaces with the operator and that part of the environment which has effect on the protection against point of
operation hazards.
(9) Safeguarding the point of operation. (i) The point of operation of presses operated in the PSDI mode
shall be safeguarded in accordance with the requirements of paragraph (c) of this section, except that the safety
distance requirements of paragraph (h)(9)(v) of this section shall be used for PSDI operation.
(ii)(A) PSDI shall be implemented only by use of light curtain (photo-electric) presence sensing devices
which meet the requirements of paragraph (c)(3)(iii)(c) of this section unless the requirements of the following
paragraph have been met.
(B) Alternatives to photo-electric light curtains may be used for PSDI when the employer can
demonstrate, through tests and analysis by the employer or the manufacturer, that the alternative is as safe as
the photo-electric light curtain, that the alternative meets the conditions of this section, has the same long term
reliability as light curtains and can be integrated into the entire safety system as provided for in this section.
Prior to use, both the employer and manufacturer must certify that these requirements and all the other
applicable requirements of this section are met and these certifications must be validated by an OSHArecognized third-party validation organization to meet these additional requirements and all the other
applicable requirements of paragraphs (a) through (h) and appendix A of this section. Three months prior to
the operation of any alternative system, the employer must notify the OSHA Directorate of Safety Standards
Programs of the name of the system to be installed, the manufacturer and the OSHA-recognized third-party
validation organization immediately. Upon request, the employer must make available to that office all tests
and analyses for OSHA review.
(iii) Individual sensing fields of presence sensing devices used to initiate strokes in the PSDI mode shall
cover only one side of the press.
(iv) Light curtains used for PSDI operation shall have minimum object sensitivity not to exceed one and
one-fourth inches (31.75 mm). Where light curtain object sensitivity is user-adjustable, either discretely or
continuously, design features shall limit the minimum object sensitivity adjustment not to exceed one and onefourth inches (31.75 mm). Blanking of the sensing field is not permitted.
(v) The safety distance (Ds) from the sensing field of the presence sensing device to the point of
operation shall be greater than or equal to the distance determined by the formula:
Ds = Hs × (Ts + Tp + Tr + 2Tm) + Dp
Where:
Ds = Minimum safety distance.
Hs = Hand speed constant of 63 inches per second (1.6 m/s).
Ts = Longest press stopping time, in seconds, computed by taking averages of multiple measurements at each of three positions
(45 degrees, 60 degrees, and 90 degrees) of crankshaft angular position; the longest of the three averages is the
stopping time to use. (Ts is defined as the sum of the kinetic energy dissipation time plus the
pneumatic/magnetic/hydraulic reaction time of the clutch/brake operating mechanism(s).)
Tp = Longest presence sensing device response time, in seconds.
Tr = Longest response time, in seconds, of all interposing control elements between the presence sensing device and the
clutch/brake operating mechanism(s).

Tm = Increase in the press stopping time at the top of the stroke, in seconds, allowed by the brake monitor for brake wear. The
time increase allowed shall be limited to no more than 10 percent of the longest press stopping time measured at the
top of the stroke, or 10 milliseconds, whichever is longer.
Dp = Penetration depth factor, required to provide for possible penetration through the presence sensing field by fingers or hand
before detection occurs. The penetration depth factor shall be determined from Graph h-1 using the minimum object
sensitivity size.

View or download PDF

(vi) The presence sensing device location shall either be set at each tool change and set-up to provide at
least the minimum safety distance, or fixed in location to provide a safety distance greater than or equal to the
minimum safety distance for all tooling set-ups which are to be used on that press.
(vii) Where presence sensing device location is adjustable, adjustment shall require the use of a special
tool available only to authorized persons.
(viii) Supplemental safeguarding shall be used to protect all areas of access to the point of operation
which are unprotected by the PSDI presence sensing device. Such supplemental safeguarding shall consist of
either additional light curtain (photo-electric) presence sensing devices or other types of guards which meet the
requirements of paragraphs (c) and (h) of this section.

(A) Presence sensing devices used as supplemental safeguarding shall not initiate a press stroke, and
shall conform to the requirements of paragraph (c)(3)(iii) and other applicable provisions of this section,
except that the safety distance shall comply with paragraph (h)(9)(v) of this section.
(B) Guards used as supplemental safeguarding shall conform to the design, construction and application
requirements of paragraph (c)(2) of this section, and shall be interlocked with the press control to prevent press
PSDI operation if the guard fails, is removed, or is out of position.
(ix) Barriers shall be fixed to the press frame or bolster to prevent personnel from passing completely
through the sensing field, where safety distance or press configuration is such that personnel could pass
through the PSDI presence sensing field and assume a position where the point of operation could be accessed
without detection by the PSDI presence sensing device. As an alternative, supplemental presence sensing
devices used only in the safeguard mode may be provided. If used, these devices shall be located so as to
detect all operator locations and positions not detected by the PSDI sensing field, and shall prevent stroking or
stop a stroke in process when any supplemental sensing field(s) are interrupted.
(x) Hand tools. Where tools are used for feeding, removal of scrap, lubrication of parts, or removal of
parts that stick on the die in PSDI operations:
(A) The minimum diameter of the tool handle extension shall be greater than the minimum object
sensitivity of the presence sensing device(s) used to initiate press strokes; or
(B) The length of the hand tool shall be such as to ensure that the operator's hand will be detected for any
safety distance required by the press set-ups.
(10) Inspection and maintenance. (i) Any press equipped with presence sensing devices for use in PSDI,
or for supplemental safeguarding on presses used in the PSDI mode, shall be equipped with a test rod of
diameter specified by the presence sensing device manufacturer to represent the minimum object sensitivity of
the sensing field. Instructions for use of the test rod shall be noted on a label affixed to the presence sensing
device.
(ii) The following checks shall be made at the beginning of each shift and whenever a die change is
made.
(A) A check shall be performed using the test rod according to the presence sensing device
manufacturer's instructions to determine that the presence sensing device used for PSDI is operational.
(B) The safety distance shall be checked for compliance with (h)(9)(v) of this section.
(C) A check shall be made to determine that all supplemental safeguarding is in place. Where presence
sensing devices are used for supplemental safeguarding, a check for proper operation shall be performed using
the test rod according to the presence sensing device manufacturer's instructions.
(D) A check shall be made to assure that the barriers and/or supplemental presence sensing devices
required by paragraph (h)(9)(ix) of this section are operating properly.
(E) A system or visual check shall be made to verify correct counterbalance adjustment for die weight
according to the press manufacturer's instructions, when a press is equipped with a slide counterbalance
system.

(iii) When presses used in the PSDI mode have flywheel or bullgear running on crankshaft mounted
journals and bearings, or a flywheel mounted on back shaft journals and bearings, periodic inspections
following the press manufacturer's recommendations shall be made to ascertain that bearings are in good
working order, and that automatic lubrication systems for these bearings (if automatic lubrication is provided)
are supplying proper lubrication. On presses with provision for manual lubrication of flywheel or bullgear
bearings, lubrication shall be provided according to the press manufacturer's recommendations.
(iv) Periodic inspections of clutch and brake mechanisms shall be performed to assure they are in proper
operating condition. The press manufacturer's recommendations shall be followed.
(v) When any check of the press, including those performed in accordance with the requirements of
paragraphs (h)(10)(ii), (iii) or (iv) of this section, reveals a condition of noncompliance, improper adjustment,
or failure, the press shall not be operated until the condition has been corrected by adjustment, replacement, or
repair.
(vi) It shall be the responsibility of the employer to ensure the competence of personnel caring for,
inspecting, and maintaining power presses equipped for PSDI operation, through initial and periodic training.
(11) Safety system certification/validation. (i) Prior to the initial use of any mechanical press in the PSDI
mode, two sets of certification and validation are required:
(A) The design of the safety system required for the use of a press in the PSDI mode shall be certified
and validated prior to installation. The manufacturer's certification shall be validated by an OSHA-recognized
third-party validation organization to meet all applicable requirements of paragraphs (a) through (h) and
appendix A of this section.
(B) After a press has been equipped with a safety system whose design has been certified and validated
in accordance with paragraph (h)(11)(i) of this section, the safety system installation shall be certified by the
employer, and then shall be validated by an OSHA-recognized third-party validation organization to meet all
applicable requirements of paragraphs (a) through (h) and appendix A of this section.
(ii) At least annually thereafter, the safety system on a mechanical power press used in the PSDI mode
shall be recertified by the employer and revalidated by an OSHA-recognized third-party validation
organization to meet all applicable requirements of paragraphs (a) through (h) and appendix A of this section.
Any press whose safety system has not been recertified and revalidated within the preceding 12 months shall
be removed from service in the PSDI mode until the safety system is recertified and revalidated.
(iii) A label shall be affixed to the press as part of each installation certification/validation and the most
recent recertification/revalidation. The label shall indicate the press serial number, the minimum safety
distance (Ds) required by paragraph (h)(9)(v) of this section, the fulfillment of design certification/validation,
the employer's signed certification, the identification of the OSHA-recognized third-party validation
organization, its signed validation, and the date the certification/validation and recertification/revalidation are
issued.
(iv) Records of the installation certification and validation and the most recent recertification and
revalidation shall be maintained for each safety system equipped press by the employer as long as the press is
in use. The records shall include the manufacture and model number of each component and subsystem, the
calculations of the safety distance as required by paragraph (h)(9)(v) of this section, and the stopping time
measurements required by paragraph (h)(2)(ii) of this section. The most recent records shall be made available
to OSHA upon request.

(v) The employer shall notify the OSHA-recognized third-party validation organization within five days
whenever a component or a subsystem of the safety system fails or modifications are made which may affect
the safety of the system. The failure of a critical component shall necessitate the removal of the safety system
from service until it is recertified and revalidated, except recertification by the employer without revalidation is
permitted when a non-critical component or subsystem is replaced by one of the same manufacture and design
as the original, or determined by the third-party validation organization to be equivalent by similarity analysis,
as set forth in appendix A.
(vi) The employer shall notify the OSHA-recognized third-party validation organization within five days
of the occurrence of any point of operation injury while a press is used in the PSDI mode. This is in addition to
the report of injury required by paragraph (g) of this section; however, a copy of that report may be used for
this purpose.
(12) Die setting and work set-up. (i) Die setting on presses used in the PSDI mode shall be performed in
accordance with paragraphs (d) and (h) of this section.
(ii) The PSDI mode shall not be used for die setting or set-up. An alternative manual cycle initiation and
control means shall be supplied for use in die setting which meets the requirements of paragraph (b)(7) of this
section.
(iii) Following a die change, the safety distance, the proper application of supplemental safeguarding,
and the slide counterbalance adjustment (if the press is equipped with a counterbalance) shall be checked and
maintained by authorized persons whose qualifications include knowledge of the safety distance, supplemental
safeguarding requirements, and the manufacturer's specifications for counterbalance adjustment. Adjustment of
the location of the PSDI presence sensing device shall require use of a special tool available only to the
authorized persons.
(13) Operator training. (i) The operator training required by paragraph (f)(2) of this section shall be
provided to the employee before the employee initially operates the press and as needed to maintain
competence, but not less than annually thereafter. It shall include instruction relative to the following items for
presses used in the PSDI mode.
(A) The manufacturer's recommended test procedures for checking operation of the presence sensing
device. This shall include the use of the test rod required by paragraph (h)(10)(i) of this section.
(B) The safety distance required.
(C) The operation, function and performance of the PSDI mode.
(D) The requirements for hand tools that may be used in the PSDI mode.
(E) The severe consequences that can result if he or she attempts to circumvent or by-pass any of the
safeguard or operating functions of the PSDI system.
(ii) The employer shall certify that employees have been trained by preparing a certification record which
includes the identity of the person trained, the signature of the employer or the person who conducted the
training, and the date the training was completed. The certification record shall be prepared at the completion
of training and shall be maintained on file for the duration of the employee's employment. The certification
record shall be made available upon request to the Assistant Secretary for Occupational Safety and Health.

APPENDIX A TO §1910.217—MANDATORY REQUIREMENTS FOR CERTIFICATION/VALIDATION OF SAFETY
SYSTEMS FOR PRESENCE SENSING DEVICE INITIATION OF MECHANICAL POWER PRESSES
Purpose
The purpose of the certification/validation of safety systems for presence sensing device initiation (PSDI) of mechanical
power presses is to ensure that the safety systems are designed, installed, and maintained in accordance with all applicable
requirements of 29 CFR 1910.217 (a) through (h) and this appendix A.

General
The certification/validation process shall utilize an independent third-party validation organization recognized by OSHA in
accordance with the requirements specified in appendix C of this section.
While the employer is responsible for assuring that the certification/validation requirements in §1910.217(h)(11) are
fulfilled, the design certification of PSDI safety systems may be initiated by manufacturers, employers, and/or their
representatives. The term manufacturers refers to the manufacturer of any of the components of the safety system. An employer
who assembles a PSDI safety system would be a manufacturer as well as employer for purposes of this standard and appendix.
The certification/validation process includes two stages. For design certification, in the first stage, the manufacturer (which
can be an employer) certifies that the PSDI safety system meets the requirements of 29 CFR 1910.217 (a) through (h) and this
appendix A, based on appropriate design criteria and tests. In the second stage, the OSHA-recognized third-party validation
organization validates that the PSDI safety system meets the requirements of 29 CFR 1910.217 (a) through (h) and this appendix
A and the manufacturer's certification by reviewing the manufacturer's design and test data and performing any additional
reviews required by this standard or which it believes appropriate.
For installation certification/validation and annual recertification/revalidation, in the first stage the employer certifies or
recertifies that the employer is installing or utilizing a PSDI safety system validated as meeting the design requirements of 29
CFR 1910.217 (a) through (h) and this appendix A by an OSHA-recognized third-party validation organization and that the
installation, operation and maintenance meet the requirements of 29 CFR 1910.217 (a) through (h) and this appendix A. In the
second stage, the OSHA-recognized third-party validation organization validates or revalidates that the PSDI safety system
installation meets the requirements of 29 CFR 1910.217 (a) through (h) and this appendix A and the employer's certification, by
reviewing that the PSDI safety system has been certified; the employer's certification, designs and tests, if any; the installation,
operation, maintenance and training; and by performing any additional tests and reviews which the validation organization
believes is necessary.

Summary
The certification/validation of safety systems for PSDI shall consider the press, controls, safeguards, operator, and
environment as an integrated system which shall comply with all of the requirements in 29 CFR 1910.217 (a) through (h) and this
appendix A. The certification/validation process shall verify that the safety system complies with the OSHA safety requirements
as follows:

A. Design Certification/Validation
1. The major parts, components and subsystems used shall be defined by part number or serial number, as appropriate, and
by manufacturer to establish the configuration of the system.
2. The identified parts, components and subsystems shall be certified by the manufacturer to be able to withstand the
functional and operational environments of the PSDI safety system.
3. The total system design shall be certified by the manufacturer as complying with all requirements in 29 CFR 1910.217
(a) through (h) and this appendix A.
4. The third-party validation organization shall validate the manufacturer's certification under paragraphs 2 and 3.

B. Installation Certification/Validation
1. The employer shall certify that the PSDI safety system has been design certified and validated, that the installation
meets the operational and environmental requirements specified by the manufacturer, that the installation drawings are accurate,
and that the installation meets the requirements of 29 CFR 1910.217 (a) through (h) and this appendix A. (The operational and
installation requirements of the PSDI safety system may vary for different applications.)
2. The third-party validation organization shall validate the employer's certifications that the PSDI safety system is design
certified and validated, that the installation meets the installation and environmental requirements specified by the manufacturer,
and that the installation meets the requirements of 29 CFR 1910.217 (a) through (h) and this appendix A.

C. Recertification/Revalidation
1. The PSDI safety system shall remain under certification/validation for the shorter of one year or until the system
hardware is changed, modified or refurbished, or operating conditions are changed (including environmental, application or
facility changes), or a failure of a critical component has occurred.
2. Annually, or after a change specified in paragraph 1., the employer shall inspect and recertify the installation as meeting
the requirements set forth under B., Installation Certification/Validation.
3. The third-party validation organization, annually or after a change specified in paragraph 1., shall validate the
employer's certification that the requirements of paragraph B., Installation Certification/Validation have been met.
(NOTE: Such changes in operational conditions as die changes or press relocations not involving disassembly or revision to
the safety system would not require recertification/revalidation.)

Certification/Validation Requirements
A. General Design Certification/Validation Requirements
1. Certification/Validation Program Requirements. The manufacturer shall certify and the OSHA-recognized third-party
validation organization shall validate that:
(a) The design of components, subsystems, software and assemblies meets OSHA performance requirements and are ready
for the intended use; and
(b) The performance of combined subsystems meets OSHA's operational requirements.
2. Certification/Validation Program Level of Risk Evaluation Requirements. The manufacturer shall evaluate and certify,
and the OSHA-recognized third-party validation organization shall validate, the design and operation of the safety system by
determining conformance with the following:
a. The safety system shall have the ability to sustain a single failure or a single operating error and not cause injury to
personnel from point of operation hazards. Acceptable design features shall demonstrate, in the following order or precedence,
that:
(1) No single failure points may cause injury; or
(2) Redundancy, and comparison and/or diagnostic checking, exist for the critical items that may cause injury, and the
electrical, electronic, electromechanical and mechanical parts and components are selected so that they can withstand operational
and external environments. The safety factor and/or derated percentage shall be specifically noted and complied with.
b. The manufacturer shall design, evaluate, test and certify, and the third-party validation organization shall evaluate and
validate, that the PSDI safety system meets appropriate requirements in the following areas.

(1) Environmental Limits
(a) Temperature
(b) Relative humidity
(c) Vibration
(d) Fluid compatability with other materials
(2) Design Limits
(a) Power requirements
(b) Power transient tolerances
(c) Compatability of materials used
(d) Material stress tolerances and limits
(e) Stability to long term power fluctuations
(f) Sensitivity to signal acquisition
(g) Repeatability of measured parameter without inadvertent initiation of a press stroke
(h) Operational life of components in cycles, hours, or both
(i) Electromagnetic tolerance to:
(1) Specific operational wave lengths; and
(2) Externally generated wave lengths
(3) New Design Certification/Validation. Design certification/validation for a new safety system, i.e., a new design or new
integration of specifically identified components and subsystems, would entail a single certification/validation which would be
applicable to all identical safety systems. It would not be necessary to repeat the tests on individual safety systems of the same
manufacture or design. Nor would it be necessary to repeat these tests in the case of modifications where determined by the
manufacturer and validated by the third-party validation organization to be equivalent by similarity analysis. Minor modifications
not affecting the safety of the system may be made by the manufacturer without revalidation.
Substantial modifications would require testing as a new safety system, as deemed necessary by the validation
organization.

B. Additional Detailed Design Certification/Validation Requirements
1. General. The manufacturer or the manufacturer's representative shall certify to and submit to an OSHA-recognized
third-party validation organization the documentation necessary to demonstrate that the PSDI safety system design is in full
compliance with the requirements of 29 CFR 1910.217(a)-(h) and this appendix A, as applicable, by means of analysis, tests, or
combination of both, establishing that the following additional certification/validation requirements are fulfilled.
2. Reaction Times. For the purpose of demonstrating compliance with the reaction time required by §1910.217(h), the tests
shall use the following definitions and requirements:

a. Reaction time means the time, in seconds, it takes the signal, required to activate/deactivate the system, to travel through
the system, measured from the time of signal initiation to the time the function being measured is completed.
b. Full stop or No movement of the slide or ram means when the crankshaft rotation has slowed to two or less revolutions
per minute, just before stopping completely.
c. Function completion means for, electrical, electromechanical and electronic devices, when the circuit produces a change
of state in the output element of the device.
d. When the change of state is motion, the measurement shall be made at the completion of the motion.
e. The generation of the test signal introduced into the system for measuring reaction time shall be such that the initiation
time can be established with an error of less than 0.5 percent of the reaction time measured.
f. The instrument used to measure reaction time shall be calibrated to be accurate to within 0.001 second.
3. Compliance with §1910.217(h)(2)(ii). For compliance with these requirements, the average value of the stopping time,
Ts, shall be the arithmetic mean of at least 25 stops for each stop angle initiation measured with the brake and/or clutch unused,
50 percent worn, and 90 percent worn. The recommendations of the brake system manufacturer shall be used to simulate or
estimate the brake wear. The manufacturer's recommended minimum lining depth shall be identified and documented, and an
evaluation made that the minimum depth will not be exceeded before the next (annual) recertification/revalidation. A correlation
of the brake and/or clutch degradation based on the above tests and/or estimates shall be made and documented. The results shall
document the conditions under which the brake and/or clutch will and will not comply with the requirement. Based upon this
determination, a scale shall be developed to indicate the allowable 10 percent of the stopping time at the top of the stroke for slide
or ram overtravel due to brake wear. The scale shall be marked to indicate that brake adjustment and/or replacement is required.
The explanation and use of the scale shall be documented.
The test specification and procedure shall be submitted to the validation organization for review and validation prior to the
test. The validation organization representative shall witness at least one set of tests.
4. Compliance with §§1910.217(h)(5)(iii) and (h)(9)(v). Each reaction time required to calculate the Safety Distance,
including the brake monitor setting, shall be documented in separate reaction time tests. These tests shall specify the acceptable
tolerance band sufficient to assure that tolerance build-up will not render the safety distance unsafe.
a. Integrated test of the press fully equipped to operate in the PSDI mode shall be conducted to establish the total system
reaction time.
b. Brakes which are the adjustable type shall be adjusted properly before the test.
5. Compliance with §1910.217(h)(2)(iii). a. Prior to conducting the brake system test required by paragraph (h)(2)(ii), a
visual check shall be made of the springs. The visual check shall include a determination that the spring housing or rod does not
show damage sufficient to degrade the structural integrity of the unit, and the spring does not show any tendency to interleave.
b. Any detected broken or unserviceable springs shall be replaced before the test is conducted. The test shall be considered
successful if the stopping time remains within that which is determined by paragraph (h)(9)(v) for the safety distance setting. If
the increase in press stopping time exceeds the brake monitor setting limit defined in paragraph (h)(5)(iii), the test shall be
considered unsuccessful, and the cause of the excessive stopping time shall be investigated. It shall be ascertained that the springs
have not been broken and that they are functioning properly.
6. Compliance with §1910.217(h)(7). a. Tests which are conducted by the manufacturers of electrical components to
establish stress, life, temperature and loading limits must be tests which are in compliance with the provisions of the National
Electrical Code.
b. Electrical and/or electronic cards or boards assembled with discreet components shall be considered a subsystem and
shall require separate testing that the subsystems do not degrade in any of the following conditions:
(1) Ambient temperature variation from −20 °C to + 50 °C.

(2) Ambient relative humidity of 99 percent.
(3) Vibration of 45G for one millisecond per stroke when the item is to be mounted on the press frame.
(4) Electromagnetic interference at the same wavelengths used for the radiation sensing field, at the power line frequency
fundamental and harmonics, and also from outogenous radiation due to system switching.
(5) Electrical power supply variations of ±15 percent.
c. The manufacturer shall specify the test requirements and procedures from existing consensus tests in compliance with
the provisions of the National Electrical Code.
d. Tests designed by the manufacturer shall be made available upon request to the validation organization. The validation
organization representative shall witness at least one set of each of these tests.
7. Compliance with §1910.217(h)(9)(iv). a. The manufacturer shall design a test to demonstrate that the prescribed
minimum object sensitivity of the presence sensing device is met.
b. The test specifications and procedures shall be made available upon request to the validation organization.
8. Compliance with §1910.217(h)(9)(x). a. The manufacturer shall design a test(s) to establish the hand tool extension
diameters allowed for variations in minimum object sensitivity response.
b. The test(s) shall document the range of object diameter sizes which will produce both single and double break
conditions.
c. The test(s) specifications and procedures shall be made available upon request to the validation organization.
9. Integrated Tests Certification/Validation. a. The manufacturer shall design a set of integrated tests to demonstrate
compliance with the following requirements:
Sections 1910.217(h)(6) (ii); (iii); (iv); (v); (vi); (vii); (viii); (ix); (xi); (xii); (xiii); (xiv); (xv); and (xvii).
b. The integrated test specifications and procedures shall be made available to the validation organization.
10. Analysis. a. The manufacturer shall submit to the validation organization the technical analysis such as Hazard
Analysis, Failure Mode and Effect Analysis, Stress Analysis, Component and Material Selection Analysis, Fluid Compatability,
and/or other analyses which may be necessary to demonstrate, compliance with the following requirements:
Sections 1910.217(h)(8) (i) and (ii); (h)(2) (ii) and (iii); (h)(3)(i) (A) and (C), and (ii); (h)(5) (i), (ii) and (iii); (h)(6) (i),
(iii), (iv), (vi), (vii), (viii), (ix), (x), (xi), (xiii), (xiv), (xv), (xvi), and (xvii); (h)(7) (i) and (ii); (h)(9) (iv), (v), (viii), (ix) and (x);
(h)(10) (i) and (ii).
11. Types of Tests Acceptable for Certification/Validation. a. Test results obtained from development testing may be used
to certify/validate the design.
b. The test results shall provide the engineering data necessary to establish confidence that the hardware and software will
meet specifications, the manufacturing process has adequate quality control and the data acquired was used to establish
processes, procedures, and test levels supporting subsequent hardware design, production, installation and maintenance.
12. Validation for Design Certification/Validation. If, after review of all documentation, tests, analyses, manufacturer's
certifications, and any additional tests which the third-party validation organization believes are necessary, the third-party
validation organization determines that the PSDI safety system is in full compliance with the applicable requirements of 29 CFR
1910.217(a) through (h) and this appendix A, it shall validate the manufacturer's certification that it so meets the stated
requirements.

C. Installation Certification/Validation Requirements
1. The employer shall evaluate and test the PSDI system installation, shall submit to the OSHA-recognized third-party
validation organization the necessary supporting documentation, and shall certify that the requirements of §1910.217(a) through
(h) and this appendix A have been met and that the installation is proper.
2. The OSHA-recognized third-party validation organization shall conduct tests, and/or review and evaluate the employer's
installation tests, documentation and representations. If it so determines, it shall validate the employer's certification that the
PSDI safety system is in full conformance with all requirements of 29 CFR 1910.217(a) through (h) and this appendix A.

D. Recertification/Revalidation Requirements
1. A PSDI safety system which has received installation certification/validation shall undergo recertification/revalidation
the earlier of:
a. Each time the systems hardware is significantly changed, modified, or refurbished;
b. Each time the operational conditions are significantly changed (including environmental, application or facility changes,
but excluding such changes as die changes or press relocations not involving revision to the safety system);
c. When a failure of a significant component has occurred or a change has been made which may affect safety; or
d. When one year has elapsed since the installation certification/validation or the last recertification/revalidation.
2. Conduct or recertification/revalidation. The employer shall evaluate and test the PSDI safety system installation, shall
submit to the OSHA-recognized third-party validation organization the necessary supporting documentation, and shall recertify
that the requirements of §1910.217(a) through (h) and this appendix are being met. The documentation shall include, but not be
limited to, the following items:
a. Demonstration of a thorough inspection of the entire press and PSDI safety system to ascertain that the installation,
components and safeguarding have not been changed, modified or tampered with since the installation certification/validation or
last recertification/revalidation was made.
b. Demonstrations that such adjustments as may be needed (such as to the brake monitor setting) have been accomplished
with proper changes made in the records and on such notices as are located on the press and safety system.
c. Demonstration that review has been made of the reports covering the design certification/validation, the installation
certification/validation, and all recertification/revalidations, in order to detect any degradation to an unsafe condition, and that
necessary changes have been made to restore the safety system to previous certification/validation levels.
3. The OSHA-recognized third-party validation organization shall conduct tests, and/or review and evaluate the employer's
installation, tests, documentation and representations. If it so determines, it shall revalidate the employer's recertification that the
PSDI system is in full conformance with all requirements of 29 CFR 1910.217(a) through (h) and this appendix A.

APPENDIX B TO §1910.217—NONMANDATORY GUIDELINES FOR CERTIFICATION/VALIDATION OF SAFETY
SYSTEMS FOR PRESENCE SENSING DEVICE INITIATION OF MECHANICAL POWER PRESSES
Objectives
This appendix provides employers, manufacturers, and their representatives, with nonmandatory guidelines for use in
developing certification documents. Employers and manufacturers are encouraged to recommend other approaches if there is a
potential for improving safety and reducing cost. The guidelines apply to certification/validation activity from design evaluation
through the completion of the installation test and the annual recertification/revalidation tests.

General Guidelines

A. The certification/validation process should confirm that hazards identified by hazard analysis, (HA), failure mode effect
analysis (FMEA), and other system analyses have been eliminated by design or reduced to an acceptable level through the use of
appropriate design features, safety devices, warning devices, or special procedures. The certification/validation process should
also confirm that residual hazards identified by operational analysis are addressed by warning, labeling safety instructions or
other appropriate means.
B. The objective of the certification/validation program is to demonstrate and document that the system satisfies
specification and operational requirements for safe operations.

Quality Control
The safety attributes of a certified/validated PSDI safety system are more likely to be maintained if the quality of the
system and its parts, components and subsystem is consistently controlled. Each manufacturer supplying parts, components,
subsystems, and assemblies needs to maintain the quality of the product, and each employer needs to maintain the system in a
non-degraded condition.

Analysis Guidelines
A. Certification/validation of hardware design below the system level should be accomplished by test and/or analysis.
B. Analytical methods may be used in lieu of, in combination with, or in support of tests to satisfy specification
requirements.
C. Analyses may be used for certification/validation when existing data are available or when test is not feasible.
D. Similarity analysis may be used in lieu of tests where it can be shown that the article is similar in design, manufacturing
process, and quality control to another article that was previously certified/validated in accordance with equivalent or more
stringent criteria. If previous design, history and application are considered to be similar, but not equal to or more exacting than
earlier experiences, the additional or partial certification/validation tests should concentrate on the areas of changed or increased
requirements.

Analysis Reports
The analysis reports should identify: (1) The basis for the analysis; (2) the hardware or software items analyzed; (3)
conclusions; (4) safety factors; and (5) limit of the analysis. The assumptions made during the analysis should be clearly stated
and a description of the effects of these assumptions on the conclusions and limits should be included.
Certification/validation by similarity analysis reports should identify, in addition to the above, application of the part,
component or subsystem for which certification/validation is being sought as well as data from previous usage establishing
adequacy of the item. Similarity analysis should not be accepted when the internal and external stresses on the item being
certified/validated are not defined.
Usage experience should also include failure data supporting adequacy of the design.

APPENDIX C TO §1910.217—MANDATORY REQUIREMENTS FOR OSHA RECOGNITION OF THIRD-PARTY
VALIDATION ORGANIZATIONS FOR THE PSDI STANDARD
This appendix prescribes mandatory requirements and procedures for OSHA recognition of third-party validation
organizations to validate employer and manufacturer certifications that their equipment and practices meet the requirements of
the PSDI standard. The scope of the appendix includes the three categories of certification/validation required by the PSDI
standard: Design Certification/Validation, Installation Certification/Validation, and Annual Recertification/Revalidation.
If further detailing of these provisions will assist the validation organization or OSHA in this activity, this detailing will be
done through appropriate OSHA Program Directives.

I. Procedure for OSHA Recognition of Validation Organizations
A. Applications
1. Eligibility. a. Any person or organization considering itself capable of conducting a PSDI-related third-party validation
function may apply for OSHA recognition.
b. However, in determining eligibility for a foreign-based third-party validation organization, OSHA shall take into
consideration whether there is reciprocity of treatment by the foreign government after consultation with relevant U.S.
government agencies.
2. Content of application. a. The application shall identify the scope of the validation activity for which the applicant
wishes to be recognized, based on one of the following alternatives:
(1) Design Certification/Validation, Installation Certification/Validation, and Annual Recertification/Revalidation;
(2) Design Certification/Validation only; or
(3) Installation/Certification/Validation and Annual Recertification/Revalidation.
b. The application shall provide information demonstrating that it and any validating laboratory utilized meet the
qualifications set forth in section II of this appendix.
c. The applicant shall provide information demonstrating that it and any validating laboratory utilized meet the program
requirements set forth in section III of this appendix.
d. The applicant shall identify the test methods it or the validating laboratory will use to test or judge the components and
operations of the PSDI safety system required to be tested by the PSDI standard and appendix A, and shall specify the reasons the
test methods are appropriate.
e. The applicant may include whatever enclosures, attachments, or exhibits the applicant deems appropriate. The
application need not be submitted on a Federal form.
f. The applicant shall certify that the information submitted is accurate.
3. Filing office location. The application shall be filed with: PSDI Certification/Validation Program, Office of Variance
Determination, Occupational Safety and Health Administration, U.S. Department of Labor, Room N3653, 200 Constitution
Avenue, NW., Washington, DC 20210.
4. Amendments and withdrawals. a. An application may be revised by an applicant at any time prior to the completion of
the final staff recommendation.
b. An application may be withdrawn by an applicant, without prejudice, at any time prior to the final decision by the
Assistant Secretary in paragraph I.B.8.b.(4) of this appendix.

B. Review and Decision Process
1. Acceptance and field inspection. All applications submitted will be accepted by OSHA, and their receipt acknowledged
in writing. After receipt of an application, OSHA may request additional information if it believes information relevant to the
requirements for recognition have been omitted. OSHA may inspect the facilities of the third-party validation organization and
any validating laboratory, and while there shall review any additional documentation underlying the application. A report shall be
made of each field inspection.
2. Requirements for recognition. The requirements for OSHA recognition of a third-party validation organization for the
PSDI standard are that the program has fulfilled the requirements of section II of this appendix for qualifications and of section

III of this appendix for program requirements, and the program has identified appropriate test and analysis methods to meet the
requirements of the PSDI standard and appendix A.
3. Preliminary approval. If, after review of the application, any additional information, and the inspection report, the
applicant and any validating laboratory appear to have met the requirements for recognition, a written recommendation shall be
submitted by the responsible OSHA personnel to the Assistant Secretary to approve the application with a supporting
explanation.
4. Preliminary disapproval. If, after review of the application, additional information, and inspection report, the applicant
does not appear to have met the requirements for recognition, the Director of the PSDI certification/validation program shall
notify the applicant in writing, listing the specific requirements of this appendix which the applicant has not met, and the reasons.
5. Revision of application. After receipt of a notification of preliminary disapproval, the applicant may submit a revised
application for further review by OSHA pursuant to subsection I.B. of this appendix or may request that the original application
be submitted to the Assistant Secretary with a statement of reasons supplied by the applicant as to why the application should be
approved.
6. Preliminary decision by Assistant Secretary. a. The Assistant Secretary, or a special designee for this purpose, will make
a preliminary decision whether the applicant has met the requirements for recognition based on the completed application file and
the written staff recommendation, as well as the statement of reasons by the applicant if there is a recommendation of
disapproval.
b. This preliminary decision will be sent to the applicant and subsequently published in the FEDERAL REGISTER.
7. Public review and comment period. a. The FEDERAL REGISTER notice of preliminary decision will provide a period of
not less than 60 calendar days for the written comments on the applicant's fulfillment of the requirements for recognition. The
application, supporting documents, staff recommendation, statement of applicant's reasons, and any comments received, will be
available for public inspection in the OSHA Docket Office.
b. If the preliminary decision is in favor of recognition, a member of the public, or if the preliminary decision is against
recognition, the applicant may request a public hearing by the close of the comment period, if it supplies detailed reasons and
evidence challenging the basis of the Assistant Secretary's preliminary decision and justifying the need for a public hearing to
bring out evidence which could not be effectively supplied through written submissions.
8. Final decision by Assistant Secretary—a. Without hearing. If there are no valid requests for a hearing, based on the
application, supporting documents, staff recommendation, evidence and public comment, the Assistant Secretary shall issue the
final decision (including reasons) of the Department of Labor on whether the applicant has demonstrated by a preponderance of
the evidence that it meets the requirements for recognition.
b. After hearing. If there is a valid request for a hearing pursuant to paragraph I.B.7.b. of this appendix, the following
procedures will be used:
(1) The Assistant Secretary will issue a notice of hearing before an administrative law judge of the Department of Labor
pursuant to the rules specified in 29 CFR part 1905, subpart C.
(2) After the hearing, pursuant to subpart C, the administrative law judge shall issue a decision (including reasons) based
on the application, the supporting documentation, the staff recommendation, the public comments and the evidence submitted
during the hearing (the record), stating whether it has been demonstrated, based on a preponderance of evidence, that the
applicant meets the requirements for recognition. If no exceptions are filed, this is the final decision of the Department of Labor.
(3) Upon issuance of the decision, any party to the hearing may file exceptions within 20 days pursuant to subpart C. If
exceptions are filed, the administrative law judge shall forward the decision, exceptions and record to the Assistant Secretary for
the final decision on the application.
(4) The Assistant Secretary shall review the record, the decision by the administrative law judge, and the exceptions.
Based on this, the Assistant Secretary shall issue the final decision (including reasons) of the Department of Labor stating
whether the applicant has demonstrated by a preponderance of evidence that it meets the requirements for recognition.

b. Publication. A notification of the final decision shall be published in the FEDERAL REGISTER.

C. Terms and Conditions of Recognition, Renewal and Revocation
1. The following terms and conditions shall be part of every recognition:
a. The recognition of any validation organization will be evidenced by a letter of recognition from OSHA. The letter will
provide the specific details of the scope of the OSHA recognition as well as any conditions imposed by OSHA, including any
Federal monitoring requirements.
b. The recognition of each validation organization will be valid for five years, unless terminated before or renewed after
the expiration of the period. The dates of the period of recognition will be stated in the recognition letter.
c. The recognized validation organization shall continue to satisfy all the requirements of this appendix and the letter of
recognition during the period of recognition.
2. A recognized validation organization may change a test method of the PSDI safety system certification/validation
program by notifying the Assistant Secretary of the change, certifying that the revised method will be at least as effective as the
prior method, and providing the supporting data upon which its conclusions are based.
3. A recognized validation organization may renew its recognition by filing a renewal request at the address in paragraph
I.A.3. of this appendix, above, not less than 180 calendar days, nor more than one year, before the expiration date of its current
recognition. When a recognized validation organization has filed such a renewal request, its current recognition will not expire
until a final decision has been made on the request. The renewal request will be processed in accordance with subsection I.B. of
this appendix, above, except that a reinspection is not required but may be performed by OSHA. A hearing will be granted to an
objecting member of the public if evidence of failure to meet the requirements of this appendix is supplied to OSHA.
4. A recognized validation organization may apply to OSHA for an expansion of its current recognition to cover other
categories of PSDI certification/validation in addition to those included in the current recognition. The application for expansion
will be acted upon and processed by OSHA in accordance with subsection I.B. of this appendix, subject to the possible
reinspection exception. If the validation organization has been recognized for more than one year, meets the requirements for
expansion of recognition, and there is no evidence that the recognized validation organization has not been following the
requirements of this appendix and the letter of recognition, an expansion will normally be granted. A hearing will be granted to
an objecting member of the public only if evidence of failure to meet the requirements of this appendix is supplied to OSHA.
5. A recognized validation organization may voluntarily terminate its recognition, either in its entirety or with respect to
any area covered in its recognition, by giving written notice to OSHA at any time. The written notice shall indicate the
termination date. A validation organization may not terminate its installation certification and recertification validation functions
earlier than either one year from the date of the written notice, or the date on which another recognized validation organization is
able to perform the validation of installation certification and recertification.
6.a. OSHA may revoke its recognition of a validation organization if its program either has failed to continue to satisfy the
requirements of this appendix or its letter of recognition, has not been performing the validation functions required by the PSDI
standard and appendix A, or has misrepresented itself in its applications. Before proposing to revoke recognition, the Agency will
notify the recognized validation organization of the basis of the proposed revocation and will allow rebuttal or correction of the
alleged deficiencies. If the deficiencies are not corrected, OSHA may revoke recognition, effective in 60 days, unless the
validation organization requests a hearing within that time.
b. If a hearing is requested, it shall be held before an administrative law judge of the Department of Labor pursuant to the
rules specified in 29 CFR part 1905, subpart C.
c. The parties shall be OSHA and the recognized validation organization. The decision shall be made pursuant to the
procedures specified in paragraphs I.B.8.b.(2) through (4) of this appendix except that the burden of proof shall be on OSHA to
demonstrate by a preponderance of the evidence that the recognition should be revoked because the validation organization either
is not meeting the requirements for recognition, has not been performing the validation functions required by the PSDI standard
and appendix A, or has misrepresented itself in its applications.

D. Provisions of OSHA Recognition
Each recognized third-party validation organization and its validating laboratories shall:
1. Allow OSHA to conduct unscheduled reviews or on-site audits of it or the validating laboratories on matters relevant to
PSDI, and cooperate in the conduct of these reviews and audits;
2. Agree to terms and conditions established by OSHA in the grant of recognition on matters such as exchange of data,
submission of accident reports, and assistance in studies for improving PSDI or the certification/validation process.

II. Qualifications
The third-party validation organization, the validating laboratory, and the employees of each shall meet the requirements
set forth in this section of this appendix.

A. Experience of Validation Organization
1. The third-party validation organization shall have legal authority to perform certification/validation activities.
2. The validation organization shall demonstrate competence and experience in either power press design, manufacture or
use, or testing, quality control or certification/validation of equipment comparable to power presses and associated control
systems.
3. The validation organization shall demonstrate a capability for selecting, reviewing, and/or validating appropriate
standards and test methods to be used for validating the certification of PSDI safety systems, as well as for reviewing judgements
on the safety of PSDI safety systems and their conformance with the requirements of this section.
4. The validating organization may utilize the competence, experience, and capability of its employees to demonstrate this
competence, experience and capability.

B. Independence of Validation Organization
1. The validation organization shall demonstrate that:
a. It is financially capable to conduct the work;
b. It is free of direct influence or control by manufacturers, suppliers, vendors, representatives of employers and
employees, and employer or employee organizations; and
c. Its employees are secure from discharge resulting from pressures from manufacturers, suppliers, vendors, employers or
employee representatives.
2. A validation organization may be considered independent even if it has ties with manufacturers, employers or employee
representatives if these ties are with at least two of these three groups; it has a board of directors (or equivalent leadership
responsible for the certification/validation activities) which includes representatives of the three groups; and it has a binding
commitment of funding for a period of three years or more.

C. Validating Laboratory
The validation organization's laboratory (which organizationally may be a part of the third-party validation organization):
1. Shall have legal authority to perform the validation of certification;

2. Shall be free of operational control and influence of manufacturers, suppliers, vendors, employers, or employee
representatives that would impair its integrity of performance; and
3. Shall not engage in the design, manufacture, sale, promotion, or use of the certified equipment.

D. Facilities and Equipment
The validation organization's validating laboratory shall have available all testing facilities and necessary test and
inspection equipment relevant to the validation of the certification of PSDI safety systems, installations and operations.

E. Personnel
The validation organization and the validating laboratory shall be adequately staffed by personnel who are qualified by
technical training and/or experience to conduct the validation of the certification of PSDI safety systems.
1. The validation organization shall assign overall responsibility for the validation of PSDI certification to an
Administrative Director. Minimum requirements for this position are a Bachelor's degree and five years professional experience,
at least one of which shall have been in responsible charge of a function in the areas of power press design or manufacture or a
broad range of power press use, or in the areas of testing, quality control, or certification/validation of equipment comparable to
power presses or their associated control systems.
2. The validating laboratory, if a separate organization from the validation organization, shall assign technical
responsibility for the validation of PSDI certification to a Technical Director. Minimum requirements for this position are a
Bachelor's degree in a technical field and five years of professional experience, at least one of which shall have been in
responsible charge of a function in the area of testing, quality control or certification/validation of equipment comparable to
power presses or their associated control systems.
3. If the validation organization and the validating laboratory are the same organization, the administrative and technical
responsibilities may be combined in a single position, with minimum requirements as described in E.1. and 2. for the combined
position.
4. The validation organization and validating laboratory shall have adequate administrative and technical staffs to conduct
the validation of the certification of PSDI safety systems.

F. Certification/Validation Mark or Logo
1. The validation organization or the validating laboratory shall own a registered certification/validation mark or logo.
2. The mark or logo shall be suitable for incorporation into the label required by paragraph (h)(11)(iii) of this section.

III. Program Requirements
A. Test and Certification/Validation Procedures
1. The validation organization and/or validating laboratory shall have established written procedures for test and
certification/validation of PSDI safety systems. The procedures shall be based on pertinent OSHA standards and test methods, or
other publicly available standards and test methods generally recognized as appropriate in the field, such as national consensus
standards or published standards of professional societies or trade associations.
2. The written procedures for test and certification/validation of PSDI systems, and the standards and test methods on
which they are based, shall be reproducible and be available to OSHA and to the public upon request.

B. Test Reports

1. A test report shall be prepared for each PSDI safety system that is tested. The test report shall be signed by a technical
staff representative and the Technical Director.
2. The test report shall include the following:
a. Name of manufacturer and catalog or model number of each subsystem or major component.
b. Identification and description of test methods or procedures used. (This may be through reference to published sources
which describe the test methods or procedures used.)
c. Results of all tests performed.
d. All safety distance calculations.
3. A copy of the test report shall be maintained on file at the validation organization and/or validating laboratory, and shall
be available to OSHA upon request.

C. Certification/Validation Reports
1. A certification/validation report shall be prepared for each PSDI safety system for which the certification is validated.
The certification/validation report shall be signed by the Administrative Director and the Technical Director.
2. The certification/validation report shall include the following:
a. Name of manufacturer and catalog or model number of each subsystem or major component.
b. Results of all tests which serve as the basis for the certification.
c. All safety distance calculations.
d. Statement that the safety system conforms with all requirements of the PSDI standard and appendix A.
3. A copy of the certification/validation report shall be maintained on file at the validation organization and/or validating
laboratory, and shall be available to the public upon request.
4. A copy of the certification/validation report shall be submitted to OSHA within 30 days of its completion.

D. Publications System
The validation organization shall make available upon request a list of PSDI safety systems which have been
certified/validated by the program.

E. Follow-up Activities
1. The validation organization or validating laboratory shall have a follow-up system for inspecting or testing
manufacturer's production of design certified/validated PSDI safety system components and subassemblies where deemed
appropriate by the validation organization.
2. The validation organization shall notify the appropriate product manufacturer(s) of any reports from employers of point
of operation injuries which occur while a press is operated in a PSDI mode.

F. Records

The validation organization or validating laboratory shall maintain a record of each certification/validation of a PSDI
safety system, including manufacturer and/or employer certification documentation, test and working data, test report,
certification/validation report, any follow-up inspections or testing, and reports of equipment failures, any reports of accidents
involving the equipment, and any other pertinent information. These records shall be available for inspection by OSHA and
OSHA State Plan offices.

G. Dispute Resolution Procedures
1. The validation organization shall have a reasonable written procedure for acknowledging and processing appeals or
complaints from program participants (manufacturers, producers, suppliers, vendors and employers) as well as other interested
parties (employees or their representatives, safety personnel, government agencies, etc.), concerning certification or validation.
2. The validation organization may charge any complainant the reasonable charge for repeating tests needed for the
resolution of disputes.

APPENDIX D TO §1910.217—NONMANDATORY SUPPLEMENTARY INFORMATION
This appendix provides nonmandatory supplementary information and guidelines to assist in the understanding and use of
29 CFR 1910.217(h) to allow presence sensing device initiation (PSDI) of mechanical power presses. Although this appendix as
such is not mandatory, it references sections and requirements which are made mandatory by other parts of the PSDI standard
and appendices.

1. General
OSHA intends that PSDI continue to be prohibited where present state-of-the-art technology will not allow it to be done
safely. Only part revolution type mechanical power presses are approved for PSDI. Similarly, only presses with a configuration
such that a person's body cannot completely enter the bed area are approved for PSDI.

2. Brake and Clutch
Flexible steel band brakes do not possess a long-term reliability against structural failure as compared to other types of
brakes, and therefore are not acceptable on presses used in the PSDI mode of operation.
Fast and consistent stopping times are important to safety for the PSDI mode of operation. Consistency of braking action is
enhanced by high brake torque. The requirement in paragraph (h)(2)(ii) defines a high torque capability which should ensure fast
and consistent stopping times.
Brake design parameters important to PSDI are high torque, low moment of inertia, low air volume (if pneumatic)
mechanisms, non-interleaving engagement springs, and structural integrity which is enhanced by over-design. The requirement in
paragrpah (h)(2)(iii) reduces the possibility of significantly increased stopping time if a spring breaks.
As an added precaution to the requirements in paragraph (h)(2)(iii), brake adjustment locking means should be secured.
Where brake springs are externally accessible, lock nuts or other means may be provided to reduce the possibility of backing off
of the compression nut which holds the springs in place.

3. Pneumatic Systems
Elevated clutch/brake air pressure results in longer stopping time. The requirement in paragraph (h)(3)(i)(C) is intended to
prevent degradation in stoping speed from higher air pressure. Higher pressures may be permitted, however, to increase clutch
torque to free “jammed” dies, provided positive measures are provided to prevent the higher pressure at other times.

4. Flywheels and Bearings
Lubrication of bearings is considered the single greatest deterrent to their failure. The manufacturer's recommended
procedures for maintenance and inspection should be closely followed.

5. Brake Monitoring
The approval of brake monitor adjustments, as required in paragraph (h)(5)(ii), is not considered a recertification, and does
not necessarily involve an on-site inspection by a representative of the validation organization. It is expected that the brake
monitor adjustment normally could be evaluated on the basis of the effect on the safety system certification/validation
documentation retained by the validation organization.
Use of a brake monitor does not eliminate the need for periodic brake inspection and maintenance to reduce the possibility
of catastrophic failures.

6. Cycle Control and Control Systems
The PSDI set-up/reset means required by paragraph (h)(6)(iv) may be initiated by the actuation of a special momentary
pushbutton or by the actuation of a special momentary pushbutton and the initiation of a first stroke with two hand controls.
It would normally be preferable to limit the adjustment of the time required in paragraph (h)(6)(vi) to a maximum of 15
seconds. However, where an operator must do many operations outside the press, such as lubricating, trimming, deburring, etc., a
longer interval up to 30 seconds is permitted.
When a press is equipped for PSDI operation, it is recommended that the presence sensing device be active as a guarding
device in other production modes. This should enhance the reliability of the device and ensure that it remains operable.
An acceptable method for interlocking supplemental guards as required by paragraph (h)(6)(xiii) would be to incorporate
the supplemental guard and the PSDI presence sensing device into a hinged arrangement in which the alignment of the presence
sensing device serves, in effect, as the interlock. If the supplemental guards are moved, the presence sensing device would
become misaligned and the press control would be deactivated. No extra microswitches or interlocking sensors would be
required.
Paragraph (h)(6)(xv) of the standard requires that the control system have provisions for an “inch” operating means; that
die-setting not be done in the PSDI mode; and that production not be done in the “inch” mode. It should be noted that the sensing
device would be by-passed in the “inch” mode. For that reason, the prohibitions against die-setting in the PSDI mode, and against
production in the “inch” mode are cited to emphasize that “inch” operation is of reduced safety and is not compatible with PSDI
or other production modes.

7. Environmental Requirements
It is the intent of paragraph (h)(7) that control components be provided with inherent design protection against operating
stresses and environmental factors affecting safety and reliability.

8. Safety system
The safety system provision continues the concept of paragraph (b)(13) that the probability of two independent failures in
the length of time required to make one press cycle is so remote as to be a negligible risk factor in the total array of equipment
and human factors. The emphasis is on an integrated total system including all elements affecting point of operation safety.
It should be noted that this does not require redundancy for press components such as structural elements, clutch/brake
mechanisms, plates, etc., for which adequate reliability may be achieved by proper design, maintenance, and inspection.

9. Safeguarding the Point of Operation
The intent of paragraph (h)(9)(iii) is to prohibit use of mirrors to “bend” a single light curtain sensing field around corners
to cover more than one side of a press. This prohibition is needed to increase the reliability of the presence sensing device in
initiating a stroke only when the desired work motion has been completed.
Object sensitivity describes the capability of a presence sensing device to detect an object in the sensing field, expressed as
the linear measurement of the smallest interruption which can be detected at any point in the field. Minimum object sensitivity

describes the largest acceptable size of the interruption in the sensing field. A minimum object sensitivity of one and one-fourth
inches (31.75 mm) means that a one and one-fourth inch (31.75 mm) diameter object will be continuously detected at all
locations in the sensing field.
In deriving the safety distance required in paragraph (h)(9)(v), all stopping time measurements should be made with
clutch/brake air pressure regulated to the press manufacturer's recommended value for full clutch torque capability. The stopping
time measurements should be made with the heaviest upper die that is planned for use in the press. If the press has a slide
counterbalance system, it is important that the counterbalance be adjusted correctly for upper die weight according to the
manufacturer's instructions. While the brake monitor setting is based on the stopping time it actually measures, i.e., the normal
stopping time at the top of the stroke, it is important that the safety distance be computed from the longest stopping time
measured at any of the indicated three downstroke stopping positions listed in the explanation of Ts. The use in the formula of
twice the stopping time increase, Tm, allowed by the brake monitor for brake wear allows for greater increases in the downstroke
stopping time than occur in normal stopping time at the top of the stroke.

10. Inspection and Maintenance. [Reserved]
11. Safety System Certification/Validation
Mandatory requirements for certification/validation of the PSDI safety system are provided in appendix A and appendix C
to this standard. Nonmandatory supplementary information and guidelines relating to certification/validation of the PSDI safety
system are provided to appendix B to this standard.

[39 FR 23502, June 27, 1974, as amended at 39 FR 41846, Dec. 3, 1974; 40 FR 3982, Jan. 27,
1975; 43 FR 49750, Oct. 24, 1978; 45 FR 8594, Feb. 8, 1980; 49 FR 18295, Apr. 30, 1984; 51
FR 34561, Sept. 29, 1986; 53 FR 8353, 8358 Mar. 14, 1988; 54 FR 24333, June 7, 1989; 61 FR
9240, Mar. 7, 1996; 69 FR 31882, June 8, 2004; 76 FR 80739, Dec. 27, 2011; 77 FR 46949,
Aug. 7, 2012; 78 FR 69550, Nov. 20, 2013]