DOE F 220.86 General Pumps

---

Overview

Certification
Input
Product Group Codes

---

Sheet 1: Certification

OMB Control Number: 1910-1400 (Expiration Date: XXXXXX XX, XXXX)

Version 5.3

DOE F 220.86

General Pumps

Product Type:

General Pumps

Status of This Certification Sheet

No Data

5.3

Overall Status of Template

No Data

Click here for instructions for completing this form

Each Importer and U.S. Manufacturer is legally required to certify the compliance of the products it imports, produces, assembles or manufactures. This party is the "Certifier" on this form. This certification may be submitted by the Importer or U.S. manufacturer or by a Third Party Representative. This party is the "Submitter" on this form.

Certifier - Party Legally Obligated to Certify Compliance

Submitter - Party Submitting This Report

The party responsible for certification is (select one only):

The party submitting this report is (select one only):

Please enter required data

Please enter required data

Certifier Contact Information

Third Party Representative Contact Information, if Applicable

Full Legal Name of Individual

Please enter required data

Full Legal Name of Individual

Please enter required data

Full Legal Name of Company

Please enter required data

Full Legal Name of Company

Please enter required data

Complete Company Mailing Address

Please enter required data

Complete Company Mailing Address

Please enter required data

Phone Number

Please enter required data

Phone Number

Please enter required data

Email Address

Please enter required data

Email Address

Please enter required data

Compliance Statement

Select one of the options for 'Submitter - Party Submitting This Report' above

Submitter Signature (Type your Full Legal Name)

Please enter required data

Date (MM/DD/YYYY)

Please enter required data

OMB Control Number: 1910-1400 (Expiration Date: XXXXXX XX, XXXX)

Paperwork Reduction Act Statement

OMB Burden Disclosure Statement

This data is being collected for manufacturers to certify compliance to DOE's energy conservation, water conservation, or design standards. The data you supply will be used by the Department to monitor compliance with the energy conservation, water conservation, and design standards and testing requirements for the consumer products and commercial and industrial equipment mandated by the Energy Policy and Conservation Act, as amended. Public reporting burden for this collection of information is estimated to average 35 hours per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Office of the Chief Information Officer, Records Management Division, IM-23, Paperwork Reduction Project (1910-1400), U.S. Department of Energy, 1000 Independence Ave SW, Washington, DC, 20585-1290; and to the Office of Management and Budget (OMB), OIRA, Paperwork Reduction Project (1910-1400), Washington, DC 20503. Notwithstanding any other provision of the law, no person is required to respond to, nor shall any person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a currently valid OMB control number. Submission of this data is mandatory.

---

Sheet 2: Input

General Pumps	General Pumps											Version 5.3		· Please enter your data in the columns shaded in gray below, using a separate line for each model. · Click on the column heading for instructions on how to complete cells in that column. · Cells highlighted in yellow indicate an "Error." "Error" means that information is missing or there is an issue with the entry. · If the "Status" for a row is "Error," you can see an explanation in the columns to the far right.
5.3
	Status of This Input Sheet		No Data				Overall Status of Template			No Data
	Certification Report						Click here for instructions for completing this form																																				The cells below provide an explanation for "Errors".					The cells below provide an explanation for "Errors".			The cells below provide an explanation for "Errors".			The cells below provide an explanation for "Errors".				The cells below provide an explanation for "Errors".				The cells below provide an explanation for "Errors".				The cells below provide an explanation for "Errors".			The cells below provide an explanation for "Errors".			The cells below provide an explanation for "Errors".				The cells below provide an explanation for "Errors".				The cells below provide an explanation for "Errors".
Line No.	Status	Manufacturer	Brand Name(s)	Basic Model Number (Number Unique to the Basic Model)	Pump Configuration	For BP Configuration: Complete Bare Pump Column Only For EM: Complete Bare Pump and Driver columns OR Alternate column For C or NC: Complete Bare Pump, Driver, and Controls columns OR Alternate column				Action	Product Group Code	Sample Size (Number of Units Tested)	Is the Certification for this Basic Model Based on a Waiver of DOE's Test Procedure Requirements?	Date of Test Procedure Waiver, if Applicable	Is the Certification based upon any Exception Relief from an Applicable Standard by DOE's Office of Hearing and Appeals?	Date of Exception Relief, if Applicable	Pump Energy Index (PEI) as Determined in Accordance with the Test Procedure in Section 431.464	Pump Total Head in Feet at Best Efficiency Point (BEP) and Nominal Speed as Determined in Accordance with the Test Procedure in Section 431.464	Volume per Unit Time (Flow Rate) in Gallons per Minute (gpm) at Best Efficiency Point (BEP) and Nominal Speed	Nominal Speed of Rotation in Revolutions per Minute (rpm)	For ST Pumps, the Bowl Diameter in Inches (in.)	Full Impeller Diameter in Inches (in.)	For RSV and ST Pumps, the Number of Stages Tested	Pump Efficiency at Best Efficiency Point (BEP) in percent (%) (Optional)	For Bare Pumps subject to the test methods prescribed in section III of appendix A to subpart Y of part 431				For Pumps Sold with an Electric Motor subject to the test methods prescribed in section IV or V of appendix A to subpart Y of part 431					For a Pump Sold with a Motor and Continuous or Non-Continuous Controls subject to the test methods prescribed in section VI or VII of appendix A to subpart Y of part 431						For a pump subject to the test methods prescribed in section IV - VII of appendix A to subpart Y of part 431 sold with electric motors regulated by DOE's energy conservation standards for electric motors at §431.25			Manufacturer Status	Brand Name(s) Status	Basic Model Number (Number Unique to the Basic Model) Status	Pump Configuration Status	Individual Model Number Covered by Basic Model (Bare Pump) Status	Individual Model Number (Driver), If Applicable Status	Individual Model Number (Controls), If Applicable Status	Alternate Single Individual Model Number for Bare Pump with Driver or Bare Pump with Driver and Controls Status	Action Status	Product Group Code Status	Sample Size (Number of Units Tested) Status	Is the Certification for this Basic Model Based on a Waiver of DOE's Test Procedure Requirements? Status	Date of Test Procedure Waiver, if Applicable Status	Is the Certification based upon any Exception Relief from an Applicable Standard by DOE's Office of Hearing and Appeals? Status	Date of Exception Relief, if Applicable Status	Pump Energy Index (PEI) as Determined in Accordance with the Test Procedure in Section 431.464 Status	Pump Total Head in Feet at Best Efficiency Point (BEP) and Nominal Speed as Determined in Accordance with the Test Procedure in Section 431.464 Status	Volume per Unit Time (Flow Rate) in Gallons per Minute (gpm) at Best Efficiency Point (BEP) and Nominal Speed Status	Nominal Speed of Rotation in Revolutions per Minute (rpm) Status	For ST Pumps, the Bowl Diameter in Inches (in.) Status	Full Impeller Diameter in Inches (in.) Status	For RSV and ST Pumps, the Number of Stages Tested Status	Pump Efficiency at Best Efficiency Point (BEP) in percent (%) (Optional) Status	For Bare Pumps subject to the test methods prescribed in section III of appendix A to subpart Y of part 431				For Pumps Sold with an Electric Motor subject to the test methods prescribed in section IV or V of appendix A to subpart Y of part 431					For a Pump Sold with a Motor and Continuous or Non-Continuous Controls subject to the test methods prescribed in section VI or VII of appendix A to subpart Y of part 431						For a pump subject to the test methods prescribed in section IV - VII of appendix A to subpart Y of part 431 sold with electric motors regulated by DOE's energy conservation standards for electric motors at §431.25
						Individual Model Number Covered by Basic Model (Bare Pump)	Individual Model Number (Driver), If Applicable	Individual Model Number (Controls), If Applicable	Alternate Single Individual Model Number for Bare Pump with Driver or Bare Pump with Driver and Controls																Calculated Driver Power Input at the 75% Load Point (or at 65% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Calculated Driver Power Input at the 100% Load Point (or at 90% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Calculated Driver Power Input at the 110% Load Point (or at 100% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Constant Load Pump Energy Rating (PERCL) (Optional)	Driver Power Input at the 75% Load Point (or at 65% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Driver Power Input at the 100% Load Point (or at 90% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Driver Power Input at the 110% Load Point (or at 100% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp)	Was the PEICL Calculated or Tested?	Constant Load Pump Energy Rating (PERCL) (Optional)	Driver Power Input to the Controls at 25% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable)	Driver Power Input to the Controls at 50% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable)	Driver Power Input to the Controls at 75% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable)	Driver Power Input (measured as the input power to the driver and controls) at 100% Load Point, Corrected to Nominal Speed, in Horsepower (hp)	Was the PEIVL Calculated or Tested?	Variable Load Pump Energy Rating (PERVL) (Optional)	Nominal Motor Efficiency in Percent (%) (If Applicable)	Motor Horsepower (hp) for the Motor with which the Pump is Being Rated (If Applicable)																									Calculated Driver Power Input at the 75% Load Point (or at 65% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Calculated Driver Power Input at the 100% Load Point (or at 90% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Calculated Driver Power Input at the 110% Load Point (or at 100% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Constant Load Pump Energy Rating (PERCL) (Optional) Status	Driver Power Input at the 75% Load Point (or at 65% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Driver Power Input at the 100% Load Point (or at 90% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Driver Power Input at the 110% Load Point (or at 100% Load Point if BEP is at Run Out), Corrected to Nominal Speed, in Horsepower (hp) Status	Was the PEICL Calculated or Tested? Status	Constant Load Pump Energy Rating (PERCL) (Optional) Status	Driver Power Input to the Controls at 25% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable) Status	Driver Power Input to the Controls at 50% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable) Status	Driver Power Input to the Controls at 75% Load Point, in Horsepower (hp) (corrected in accordance with the test procedure, if applicable) Status	Driver Power Input (measured as the input power to the driver and controls) at 100% Load Point, Corrected to Nominal Speed, in Horsepower (hp) Status	Was the PEIVL Calculated or Tested? Status	Variable Load Pump Energy Rating (PERVL) (Optional) Status	Nominal Motor Efficiency in Percent (%) (If Applicable) Status	Motor Horsepower (hp) for the Motor with which the Pump is Being Rated (If Applicable) Status
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

---

Sheet 3: Product Group Codes

The following is a description of each product group code:
Product Group Code	Equipment Class Abbreviation	Equipment Family	Nominal Speed of Rotation	Operating Mode
1	ESCC.1800.CL	End suction close-coupled	1800	Constant load
2	ESCC.3600.CL	End suction close-coupled	3600	Constant Load
3	ESCC.1800.VL	End suction close-coupled	1800	Variable Load
4	ESCC.3600.VL	End suction close-coupled	3600	Variable Load
5	ESFM.1800.CL	End suction frame mounted/own bearings	1800	Constant Load
6	ESFM.3600.CL	End suction frame mounted/own bearings	3600	Constant Load
7	ESFM.1800.VL	End suction frame mounted/own bearings	1800	Variable Load
8	ESFM.3600.VL	End suction frame mounted/own bearings	3600	Variable Load
9	IL.1800.CL	In-line	1800	Constant Load
10	IL.3600.CL	In-line	3600	Constant Load
11	IL.1800.VL	In-line	1800	Variable Load
12	IL.3600.VL	In-line	3600	Variable Load
13	RSV.1800.CL	Radially split, multi-stage, vertical, in-line casing diffuser	1800	Constant Load
14	RSV.3600.CL	Radially split, multi-stage, vertical, in-line casing diffuser	3600	Constant Load
15	RSV.1800.VL	Radially split, multi-stage, vertical, in-line casing diffuser	1800	Variable Load
16	RSV.3600.VL	Radially split, multi-stage, vertical, in-line casing diffuser	3600	Variable Load
17	ST.1800.CL	Submersible turbine	1800	Constant Load
18	ST.3600.CL	Submersible turbine	3600	Constant Load
19	ST.1800.VL	Submersible turbine	1800	Variable Load
20	ST.3600.VL	Submersible turbine	3600	Variable Load