| Instructions for Emissions Testing Template | |||||||||||||
| 1) | Three different tabs are provided based on the type of test performed: | ||||||||||||
| Emissions source test results should be entered in the "Emissions_Data" tab | |||||||||||||
| Fuel gas sampling data should be entered in the "FuelGas_Data" tab | |||||||||||||
| Wastewater sampling data should be entered in the "Wastewater_Data" tab | |||||||||||||
| 2) | Data should be entered into the white cells only; blue cells are intended for calculations | ||||||||||||
| 3) | A list of pollutants, their CAS No./Pollutant Code, and their pollutant category are provided in the "Pollutants" tab | ||||||||||||
| 4) | Guidance for process data to report is provided below | ||||||||||||
 
		 | 
		|||||||||||||
| Qa | Qs | %M | Ts | Ps | %O2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Emissions Test Data | Use full detection limits in averages? | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Instruction: | Enter APCD used during test. Enter more than 1 APCD if needed (e.g., ESP1/WS1) | Enter other source reduction measures used during emission test (e.g., low NOx burners or catalyst additives) | General source description, e.g., Fluid catalytic cracking unit; semiregenerative catalytic reforming unit; etc. | Assign a unique ID for each test report | Enter start date | Enter the pollutant information for each pollutant measured (see pollutant tab for list of possible pollutants) | Enter the feed input rate or production rate in units as specified in table for Question 16 of Part I (see instructions tab for details) | Provide other processing rate data as specified in the instructions for the type of unit tested. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Field: | Process Throughput or Production Rate | Secondary Processing Rate Data | Outlet - Run 1 Stack Gas Parameters | Outlet - Run 2 Stack Gas Parameters | Outlet - Run 3 Stack Gas Parameters | Outlet - Average Stack Gas Parameters | Outlet - Run 1 Emissions Data | Outlet - Run 2 Emissions Data | Outlet - Run 3 Emissions Data | Outlet - Average Emissions Data | Suspect Data | Exclude | Comment | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Facility ID Number | Unit ID Number | APCD_ID(s) | Combustion controls used to reduce air pollution (from combustion sources) | General Description | Test Report ID | Test Date (mm/dd/yyyy)  | 
		Other data provided | Pollutant Name | Pollutant CAS No. | Pollutant Class | Test Method | Run 1 Hourly Production Rate (value)  | 
		Run 2 Hourly Production Rate (value)  | 
		Run 3 Hourly Production Rate (value)  | 
		Average Hourly Production Rate (value)  | 
		Hourly Production Rate (units)  | 
		Production comment | Run 1 Hourly Production Rate (value)  | 
		Run 2 Hourly Production Rate (value)  | 
		Run 3 Hourly Production Rate (value)  | 
		Average Hourly Production Rate (value)  | 
		Hourly Production Rate (units)  | 
		Production comment | Run 1 Airflow Rate_Outlet (acfm)  | 
		Run 1 Airflow Rate_Outlet (dscfm)  | 
		Run 1 Gas Moisture_Outlet (%)  | 
		Run 1 Gas Temp_Outlet (F)  | 
		Run 1 Gas Pressure_Outlet (in. Hg)  | 
		Run 1 Gas Oxygen_Outlet (%)  | 
		Run 2 Airflow Rate_Outlet (acfm)  | 
		Run 2 Airflow Rate_Outlet (dscfm)  | 
		Run 2 Gas Moisture_Outlet (%)  | 
		Run 2 Gas Temp_Outlet (F)  | 
		Run 2 Gas Pressure_Outlet (in. Hg)  | 
		Run 2 Gas Oxygen_Outlet (%)  | 
		Run 3 Airflow Rate_Outlet (acfm)  | 
		Run 3 Airflow Rate_Outlet (dscfm)  | 
		Run 3 Gas Moisture_Outlet (%)  | 
		Run 3 Gas Temp_Outlet (F)  | 
		Run 3 Gas Pressure_Outlet (in. Hg)  | 
		Run 3 Gas Oxygen_Outlet (%)  | 
		Average Airflow Rate_Outlet (acfm)  | 
		Average Airflow Rate_Outlet (dscfm)  | 
		Average Gas Moisture_Outlet (%)  | 
		Average Gas Temp_Outlet (F)  | 
		Average Gas Pressure_Outlet (in. Hg)  | 
		Average Gas Oxygen_Outlet (%)  | 
		Run 1_Outlet concentration  | 
		Run 1 Outlet concentration units | Run 1 Outlet Detect Flag | Run 1_Outlet (lb/hr)  | 
		Run 1_Outlet (lb/production)  | 
		Run 1 Lb/Production units  | 
		Run 2_Outlet concentration  | 
		Run 2 Outlet concentration units | Run 2 Outlet Detect Flag | Run 2_Outlet (lb/hr)  | 
		Run 2_Outlet (lb/production)  | 
		Run 2 Lb/Production units  | 
		Run 3_Outlet concentration  | 
		Run 3 Outlet concentration units | Run 3 Outlet Detect Flag | Run 3_Outlet (lb/hr)  | 
		Run 3_Outlet (lb/production)  | 
		Run 3 Lb/Production units  | 
		Average_Outlet concentration  | 
		Average Outlet concentration units | Count Outlet Non-Detect Runs | Average_Outlet (lb/hr)  | 
		Average_Outlet (lb/production)  | 
		Average Lb/Production units  | 
		Suspect Data? | Cause for suspicion | Exclude Data? | Reason for excluding | Test Report Comment | |
| #DIV/0! | #DIV/0! | #DIV/0! | #DIV/0! | #DIV/0! | #DIV/0! | #DIV/0! | #DIV/0! | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| link ro Run 1 | link to Run 1 | link ro Run 1 | link to Run 1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Emissions Test Data | ||||||||||||||||||||||||||||||||||||
| Instruction: | General source description, e.g., mix drum for X,Y,Z units; mix drum for fuel gas system 1; etc. | Assign a unique ID for each test report | Enter start date | Enter the pollutant information for each pollutant measured (see pollutant tab for list of possible pollutants) | Enter the fuel gas flow rate or usage rates (in scfm at 60°F) from measurement data, company records, or engineering analyses | |||||||||||||||||||||||||||||||
| Field: | Process Throughput or Production Rate | Run 1 | Run 2 | Run 3 | Outlet - Average Emissions Data | Suspect Data | Exclude | Comment | ||||||||||||||||||||||||||||
| Facility ID Number | Fuel gas mix drum ID | General Description | Test Report ID | Test Date (mm/dd/yyyy)  | 
		Other data provided | Pollutant Name | Pollutant CAS No. | Pollutant Class | Test Method | Run 1 Fuel Gas Flow Rate (scfm)  | 
		Run 2 Fuel Gas Flow Rate (scfm)  | 
		Run 3 Fuel Gas Flow Rate (scfm)  | 
		Average Fuel Gas Flow Rate (scfm)  | 
		Production comment | Run 1 Concentration | Run 1 Concentration units | Run 1 Detect Flag | Run 1 Mass flow (lb/hr)  | 
		Run 2 Concentration | Run 2 Concentration units | Run 2 Detect Flag | Run 2 Mass flow (lb/hr)  | 
		Run 3 Concentration | Run 3 Concentration units | Run 3 Detect Flag | Run 3 Mass flow (lb/hr)  | 
		Average concentration | Average concentration units | Count Non-Detect Runs | Average Mass flow (lb/hr)  | 
		Suspect Data? | Cause for suspicion | Exclude Data? | Reason for excluding | Test Report Comment | |
| #DIV/0! | ||||||||||||||||||||||||||||||||||||
| link ro Run 1 | link ro Run 1 | |||||||||||||||||||||||||||||||||||
| Well-Mixed Assessment | F_bio Determination | |||||||||||||||||||||||||||||||||||||||||||||
| Criteria or Description | Value | Compound | F_bio | First-order biorate, k1 (L/gMLVSS-hr) | ||||||||||||||||||||||||||||||||||||||||||
| Meets defintion of EBU | Benzene Only Spike | |||||||||||||||||||||||||||||||||||||||||||||
| Meets characteristics in Table 1 | Benzene | |||||||||||||||||||||||||||||||||||||||||||||
| Meets specifications in Table 2 | Multi-compound Spike | |||||||||||||||||||||||||||||||||||||||||||||
| Calculated mixing time | Benzene | |||||||||||||||||||||||||||||||||||||||||||||
| Forms used to calculate mixing time | Toluene | |||||||||||||||||||||||||||||||||||||||||||||
| Xylene | ||||||||||||||||||||||||||||||||||||||||||||||
| Naphthalene | ||||||||||||||||||||||||||||||||||||||||||||||
| Waste Water Sampling Data | ||||||||||||||||||||||||||||||||||||||||||||||
| Instruction: | General source description, e.g., submerged aeration activated sludge unit; UNOX system; etc. | Assign a unique ID for each test report | Enter start date | Enter the pollutant information for each pollutant measured (see pollutant tab for list of possible pollutants) | Enter the wastewater flow rate and other parameters of the wastewater of unit tested. | |||||||||||||||||||||||||||||||||||||||||
| Field: | Process Throughput or Production Rate | Influent Sample Results | Within Biological Treatment Unit Results | Effluent Sample Results | Outlet - Average Stack Gas Parameters | Suspect Data | Exclude | Comment | ||||||||||||||||||||||||||||||||||||||
| Facility ID Number | Unit ID Number | General Description | Test Report ID | Test Date (mm/dd/yyyy)  | 
		Other data provided | Pollutant Name | Pollutant CAS No. | Pollutant Class | Test Method | Average wastewater flow rate during test (m3/sec) | Wastewater pH | Wastewater temperature | Volatile suspended solids in biological treatment unit (g/L) (units)  | 
		Total horsepower to surface aerators (HP) | Total air flow rate to diffused aerators (scfm at 68°F) | Other information or comment | Run 1 Airflow Rate_Outlet (acfm)  | 
		Run 1 Airflow Rate_Outlet (dscfm)  | 
		Run 1 Gas Moisture_Outlet (%)  | 
		Run 1 Gas Temp_Outlet (F)  | 
		Run 1 Gas Pressure_Outlet (in. Hg)  | 
		Run 1 Gas Oxygen_Outlet (%)  | 
		Run 2 Airflow Rate_Outlet (acfm)  | 
		Run 2 Airflow Rate_Outlet (dscfm)  | 
		Run 2 Gas Moisture_Outlet (%)  | 
		Run 2 Gas Temp_Outlet (F)  | 
		Run 2 Gas Pressure_Outlet (in. Hg)  | 
		Run 2 Gas Oxygen_Outlet (%)  | 
		Run 3 Airflow Rate_Outlet (acfm)  | 
		Run 3 Airflow Rate_Outlet (dscfm)  | 
		Run 3 Gas Moisture_Outlet (%)  | 
		Run 3 Gas Temp_Outlet (F)  | 
		Run 3 Gas Pressure_Outlet (in. Hg)  | 
		Run 3 Gas Oxygen_Outlet (%)  | 
		Average Airflow Rate_Outlet (acfm)  | 
		Average Airflow Rate_Outlet (dscfm)  | 
		Average Gas Moisture_Outlet (%)  | 
		Average Gas Temp_Outlet (F)  | 
		Average Gas Pressure_Outlet (in. Hg)  | 
		Average Gas Oxygen_Outlet (%)  | 
		Suspect Data? | Cause for suspicion | Exclude Data? | Reason for excluding | Test Report Comment | |
| Pollutant_Class | CAS_Number | Substance | |
| 1 | Criteria Pollutants | 630-08-0 | Carbon monoxide | 
| 2 | Criteria Pollutants | PM10-PRI | Particulate matter (PM) ≤ 10 µm | 
| 3 | Criteria Pollutants | PM10-FIL | Filterable PM ≤ 10 µm | 
| 4 | Criteria Pollutants | PM25-PRI | PM ≤ 2.5 µm | 
| 5 | Criteria Pollutants | PM25-FIL | Filterable PM ≤ 2.5 µm | 
| 6 | Criteria Pollutants | PM-CON | Condensable PM | 
| 7 | Criteria Pollutants | 10102-44-0 | Nitrogen dioxide | 
| 8 | Criteria Pollutants | NOX | Nitrogen oxides | 
| 9 | Criteria Pollutants | 7446-09-5 | Sulfur dioxide | 
| 10 | Criteria Pollutants | VOC | Volatile organic compounds | 
| 11 | VOC | 74-85-1 | Ethylene | 
| 12 | VOC | 74-86-2 | Acetylene | 
| 13 | VOC | 74-98-6 | Propane | 
| 14 | VOC | 115-07-1 | Propylene | 
| 15 | VOC | 463-49-0 | Propadiene | 
| 16 | VOC | 106-97-8 | n-Butane | 
| 17 | VOC | 75-28-5 | Isobutane | 
| 18 | VOC | 106-98-9 | 1-Butene | 
| 19 | VOC | 107-01-7 | 2-Butene | 
| 20 | VOC | 115-11-7 | Isobutene | 
| 21 | VOC | 590-19-2 | 1,2-Butadiene | 
| 22 | VOC | 109-66-0 | n-pentane | 
| 23 | VOC | 78-78-4 | 2-Methylbutane | 
| 24 | VOC | 287-92-3 | Cyclopentane | 
| 25 | VOC | 591-95-7 | 1,2-Pentadiene | 
| 26 | VOC | 1574-41-0 | 1-cis-3-Pentadiene | 
| 27 | VOC | 2004-70-8 | 1-trans-3-Pentadiene | 
| 28 | VOC | 591-93-5 | 1,4-Pentadiene | 
| 29 | VOC | 591-96-8 | 2,3-Pentadiene | 
| 30 | VOC | 598-25-4 | 3-Methyl-1,2-butadiene | 
| 31 | VOC | 78-79-5 | 2-Methyl-1,3-butadiene | 
| 32 | VOC | 542-92-7 | Cyclopentadiene | 
| 33 | VOC | 110-82-7 | Cyclohexane | 
| 34 | VOC | 108-87-2 | Methylcylcohexane | 
| 35 | VOC | 142-82-5 | Heptane (and isomers) | 
| 36 | VOC | 111-65-9 | Octane (and isomers) | 
| 37 | VOC | 78-93-3 | Methyl ethyl ketone | 
| 38 | VOC | 25551-13-7 | Trimethylbenzene(s) | 
| 39 | Volatile Organic HAP | 75-07-0 | Acetaldehyde | 
| 40 | Volatile Organic HAP | 107-02-8 | Acrolein | 
| 41 | Volatile Organic HAP | 62-53-3 | Analine | 
| 42 | Volatile Organic HAP | 71-43-2 | Benzene | 
| 43 | Volatile Organic HAP | 74-83-9 | Bromomethane | 
| 44 | Volatile Organic HAP | 106-99-0 | 1,3-Butadiene | 
| 45 | Volatile Organic HAP | 75-00-3 | Chloroethane | 
| 46 | Volatile Organic HAP | 67-66-3 | Chloroform | 
| 47 | Volatile Organic HAP | 74-87-3 | Chloromethane | 
| 48 | Volatile Organic HAP | 98-82-8 | Cumene | 
| 49 | Volatile Organic HAP | 106-93-4 | 1,2-Dibromoethane | 
| 50 | Volatile Organic HAP | 106-46-7 | 1,4-Dichlorobenzene | 
| 51 | Volatile Organic HAP | 75-34-3 | 1,1-Dichloroethane | 
| 52 | Volatile Organic HAP | 107-06-2 | 1,2-Dichloroethane | 
| 53 | Volatile Organic HAP | 75-35-4 | 1,1-Dichloroethylene | 
| 54 | Volatile Organic HAP | 78-87-5 | 1,2-Dichloropropane | 
| 55 | Volatile Organic HAP | 542-75-6 | 1,3-Dichloropropene | 
| 56 | Volatile Organic HAP | 111-42-2 | Diethanolamine | 
| 57 | Volatile Organic HAP | 100-41-4 | Ethylbenzene | 
| 58 | Volatile Organic HAP | 50-00-0 | Formaldehyde | 
| 59 | Volatile Organic HAP | 67-72-1 | Hexachloroethane | 
| 60 | Volatile Organic HAP | 110-54-3 | n-Hexane | 
| 61 | Volatile Organic HAP | 67-56-1 | Methanol | 
| 62 | Volatile Organic HAP | 108-10-1 | Methyl isobutyl ketone | 
| 63 | Volatile Organic HAP | 1634-04-4 | Methyl tert-butyl ether | 
| 64 | Volatile Organic HAP | 100-42-5 | Styrene | 
| 65 | Volatile Organic HAP | 79-34-5 | 1,1,2,2-Tetrachloroethane | 
| 66 | Volatile Organic HAP | 127-18-4 | Tetrachloroethylene | 
| 67 | Volatile Organic HAP | 108-88-3 | Toluene | 
| 68 | Volatile Organic HAP | 79-00-5 | 1,1,2-Trichloroethane | 
| 69 | Volatile Organic HAP | 79-01-6 | Trichloroethylene | 
| 70 | Volatile Organic HAP | 121-44-8 | Triethylamine | 
| 71 | Volatile Organic HAP | 540-84-1 | 2,2,4-Trimethylpentane | 
| 72 | Volatile Organic HAP | 593-60-2 | Vinyl bromide | 
| 73 | Volatile Organic HAP | 75-01-4 | Vinyl chloride | 
| 74 | Volatile Organic HAP | 95-47-6 | o-Xylene | 
| 75 | Volatile Organic HAP | 108-38-3 | m-Xylene | 
| 76 | Volatile Organic HAP | 106-42-3 | p-Xylene | 
| 77 | Volatile Organic HAP | 1330-20-7 | Xylenes (total) | 
| 78 | Semi-Volatile/Non-Volatile Organic HAP | 83-32-9 | Acenaphthene | 
| 79 | Semi-Volatile/Non-Volatile Organic HAP | 208-96-8 | Acenaphthylene | 
| 80 | Semi-Volatile/Non-Volatile Organic HAP | 120-12-7 | Anthracene | 
| 81 | Semi-Volatile/Non-Volatile Organic HAP | 56-55-3 | Benzo(a)anthracene | 
| 82 | Semi-Volatile/Non-Volatile Organic HAP | 50-32-8 | Benzo(a)pyrene | 
| 83 | Semi-Volatile/Non-Volatile Organic HAP | 205-99-2 | Benzo(b)fluoranthene | 
| 84 | Semi-Volatile/Non-Volatile Organic HAP | 192-97-2 | Benzo(e)pyrene | 
| 85 | Semi-Volatile/Non-Volatile Organic HAP | 191-24-2 | Benzo(g,h,i)perylene | 
| 86 | Semi-Volatile/Non-Volatile Organic HAP | 207-08-9 | Benzo(k)fluoranthene | 
| 87 | Semi-Volatile/Non-Volatile Organic HAP | 92-52-4 | Biphenyl | 
| 88 | Semi-Volatile/Non-Volatile Organic HAP | 117-81-7 | Bis(2-ethyl hexyl)phthalate | 
| 89 | Semi-Volatile/Non-Volatile Organic HAP | 91-58-7 | 2-Chloronaphthalene | 
| 90 | Semi-Volatile/Non-Volatile Organic HAP | 108-39-4 | m-Cresol | 
| 91 | Semi-Volatile/Non-Volatile Organic HAP | 95-48-7 | o-Cresol | 
| 92 | Semi-Volatile/Non-Volatile Organic HAP | 106-44-5 | p-Cresol | 
| 93 | Semi-Volatile/Non-Volatile Organic HAP | 1319-77-3 | Cresols (total) | 
| 94 | Semi-Volatile/Non-Volatile Organic HAP | 218-01-9 | Chrysene | 
| 95 | Semi-Volatile/Non-Volatile Organic HAP | 53-70-3 | Dibenz(a,h)anthracene | 
| 96 | Semi-Volatile/Non-Volatile Organic HAP | 84-74-2 | di-n-Butyl phthalate | 
| 97 | Semi-Volatile/Non-Volatile Organic HAP | 84-66-2 | Diethyl-phthalate | 
| 98 | Semi-Volatile/Non-Volatile Organic HAP | 57-97-6 | 7,12-Dimethylbenz(a) anthracene | 
| 99 | Semi-Volatile/Non-Volatile Organic HAP | 206-44-0 | Fluoranthene | 
| 100 | Semi-Volatile/Non-Volatile Organic HAP | 86-73-7 | Fluorene | 
| 101 | Semi-Volatile/Non-Volatile Organic HAP | 193-39-5 | Indeno(1,2,3-cd) pyrene | 
| 102 | Semi-Volatile/Non-Volatile Organic HAP | 56-49-5 | 3-Methylchloranthrene | 
| 103 | Semi-Volatile/Non-Volatile Organic HAP | 91-57-6 | 2-Methylnaphthalene | 
| 104 | Semi-Volatile/Non-Volatile Organic HAP | 218-01-9 | Chrysene | 
| 105 | Semi-Volatile/Non-Volatile Organic HAP | 91-20-3 | Naphthalene | 
| 106 | Semi-Volatile/Non-Volatile Organic HAP | 198-55-0 | Perylene | 
| 107 | Semi-Volatile/Non-Volatile Organic HAP | 85-01-8 | Phenanthrene | 
| 108 | Semi-Volatile/Non-Volatile Organic HAP | 108-95-2 | Phenol | 
| 109 | Semi-Volatile/Non-Volatile Organic HAP | 129-00-0 | Pyrene | 
| 110 | Dioxins Furans and PCBs | 1746-01-6 | Dioxin: 4D 2378 | 
| 111 | Dioxins Furans and PCBs | 40321-76-4 | Dioxin: 5D 12378 | 
| 112 | Dioxins Furans and PCBs | 39227-28-6 | Dioxin: 6D 123478 | 
| 113 | Dioxins Furans and PCBs | 57653-85-7 | Dioxin: 6D 123678 | 
| 114 | Dioxins Furans and PCBs | 19408-74-3 | Dioxin: 6D 123789 | 
| 115 | Dioxins Furans and PCBs | 35822-46-9 | Dioxin: 7D 1234678 | 
| 116 | Dioxins Furans and PCBs | 3268-87-9 | Dioxin: 8D | 
| 117 | Dioxins Furans and PCBs | 132-64-9 | Dibenzofurans | 
| 118 | Dioxins Furans and PCBs | 51207-31-9 | Furan: 4F 2378 | 
| 119 | Dioxins Furans and PCBs | 57117-41-6 | Furan: 5F 12378 | 
| 120 | Dioxins Furans and PCBs | 57117-31-4 | Furan: 5F 23478 | 
| 121 | Dioxins Furans and PCBs | 70648-26-9 | Furan: 6F 123478 | 
| 122 | Dioxins Furans and PCBs | 57117-44-9 | Furan: 6F 123678 | 
| 123 | Dioxins Furans and PCBs | 72918-21-9 | Furan: 6F 123789 | 
| 124 | Dioxins Furans and PCBs | 60851-34-5 | Furan: 6F 234678 | 
| 125 | Dioxins Furans and PCBs | 67562-39-4 | Furan: 7F 1234678 | 
| 126 | Dioxins Furans and PCBs | 55673-89-7 | Furan: 7F 1234789 | 
| 127 | Dioxins Furans and PCBs | 39001-02-0 | Furan: 8F | 
| 128 | Dioxins Furans and PCBs | 1336-36-3 | Polychlorinated biphenyls (total) | 
| 129 | Metal HAP | 7440-36-0 | Antimony | 
| 130 | Metal HAP | 7440-38-2 | Arsenic | 
| 131 | Metal HAP | 7440-41-7 | Beryllium | 
| 132 | Metal HAP | 7440-43-9 | Cadmium | 
| 133 | Metal HAP | 18540-29-9 | Chromium (hexavalent) | 
| 134 | Metal HAP | 7440-47-3 | Chromium (total) | 
| 135 | Metal HAP | 7440-48-4 | Cobalt | 
| 136 | Metal HAP | 7439-92-1 | Lead | 
| 137 | Metal HAP | 7439-96-5 | Manganese | 
| 138 | Metal HAP | 7439-97-6 | Mercury | 
| 139 | Metal HAP | 7440-02-0 | Nickel | 
| 140 | Metal HAP | 7782-49-2 | Selenium | 
| 141 | Other Inorganic HAP | 75-15-0 | Carbon disulfide | 
| 142 | Other Inorganic HAP | 463-58-1 | Carbonyl sulfide | 
| 143 | Other Inorganic HAP | 7782-50-5 | Chlorine | 
| 144 | Other Inorganic HAP | 7647-01-0 | Hydrogen chloride | 
| 145 | Other Inorganic HAP | 74-90-8 | Hydrogen cyanide (& cyanide compounds) | 
| 146 | Other Inorganic HAP | 7664-39-3 | Hydrogen fluoride | 
| 147 | Other Inorganic HAP | 7723-14-0 | Phosphorus | 
| 148 | Other Compounds | 7664-41-7 | Ammonia | 
| 149 | Other Compounds | 74-84-0 | Ethane | 
| 150 | Other Compounds | 7783-06-4 | Hydrogen sulfide | 
| 151 | Other Compounds | 7440-39-3 | Barium | 
| 152 | Other Compounds | 7440-50-8 | Copper | 
| 153 | Other Compounds | 7439-98-7 | Molybdenum | 
| 154 | Other Compounds | 7440-62-2 | Vanadium | 
| 155 | Other Compounds | 7440-66-6 | Zinc | 
| 156 | Surrogate | HHV | Higher Heating Value (HHV) | 
| 157 | Surrogate | THC | Total Hydrocarbon (THC) | 
| 158 | Surrogate | TRS | Total Reduced Sulfur (TRS) | 
| 159 | Surrogate | Sulfide | Sulfide | 
| 160 | Surrogate | BOD5 | 5-day Biological Oxygen Demand | 
| 161 | Surrogate | COD | Chemical Oxygen Demand | 
| File Type | application/vnd.ms-excel | 
| Author | dbullock | 
| Last Modified By | Jeff Coburn | 
| File Modified | 2011-03-18 | 
| File Created | 2011-02-02 |